Welch Allyn AT-1 Manual Download Page 33

Page: 33 / 52

AT-1 User Guide Art. No. 2. 510 270

Settings

Myogram Filter

The

Myogram filter

suppresses disturbances caused by strong muscle tremor. The set value will be the new upper limit

of the frequency range as soon as the

FILT

key is switched on or programmed as default when the unit is switched on.

When the filter is active the

‘FILT’

lamp on the unit is lit. Select the myogram filter settings as follows:

Myogram Filter

Entry Key Sequence

Setting

Confirm

ALT

Myogram Filter 25 Hz

Press
STOP

Key

Myogram Filter 35 Hz

Myo. Filt. ON when switching on unit

(marked on printout with +)

Myo. Filt. OFF when switching on unit

(marked on printout with –)

The myogram filter is switched on and off manually with the

FILT

key

Following an auto mode recording, the ECG is stored unfiltered, it is therefore possible to print the stored ECG either
with or without passing the myogram filter. Filter ON is indicated by the control lamp marked

‘FILTER’

When the

FILT

key is pressed again, the filter is switched off and the indicator lamp goes out. The cutoff frequency of

the myogram filter is set to either 25 or 35 Hz.

Settings

Myogram Filter

The

Myogram filter

suppresses disturbances caused by strong muscle tremor. The set value will be the new upper limit

of the frequency range as soon as the

FILT

key is switched on or programmed as default when the unit is switched on.

When the filter is active the

‘FILT’

lamp on the unit is lit. Select the myogram filter settings as follows:

Myogram Filter

Entry Key Sequence

Setting

Confirm

ALT

Myogram Filter 25 Hz

Press
STOP

Key

Myogram Filter 35 Hz

Myo. Filt. ON when switching on unit

(marked on printout with +)

Myo. Filt. OFF when switching on unit

(marked on printout with –)

The myogram filter is switched on and off manually with the

FILT

key

‘FILTER’

When the

FILT

key is pressed again, the filter is switched off and the indicator lamp goes out. The cutoff frequency of

the myogram filter is set to either 25 or 35 Hz.

Summary of Contents for AT-1





















































Search results

Summary of Contents for AT-1

Reviews:

Brands by name

Popular brands

Welch Allyn AT-1, Manual

Search results

Summary of Contents for AT-1

Reviews:

Brands by name

Popular brands