background image

Part number 644-500-065/0200

2

QB-180/300 Oil Burners Series 2 

— Burner Manual

Hazard definitions

The following defined terms are used throughout this manual to bring attention to the presence of hazards of
various risk levels or to important information concerning the life of the product.

IMPORTANT! — Read this page first

! ! !

Indicates presence of hazards that will
cause severe personal injury, death or
substantial property damage.

Indicates presence of hazards that can
cause severe personal injury, death or
substantial property damage.

Indicates presence of hazards that will
or can cause minor personal injury or
property damage.

Indicates special instructions on
installation, operation or maintenance
that are important but not related to
personal injury or property damage.

Read and follow instructions below to install or service the burner to reduce risk of severe personal
injury, death or substantial property damage.

Appliance must be connected to a flue with
sufficient draft at all times to assure proper
operation.

Do not use crankcase drainings or any oil
containing gasoline as it is more combus-
tible than No. 1 or No. 2 fuel oil.

Do not attempt to start burner when excess
oil has accumulated in combustion cham-
ber, when boiler is full of vapor, or when
combustion chamber is very hot.

Always keep manual fuel supply valve shut
off if burner is shut down for an extended
period of time.

Do not start burner unless flue collector
hood, jacket cap, flue cap and burner
mounting door are secured in place.

Never burn garbage or paper in the appli-
ance.

Never leave combustible material around
appliance.

Summary of Contents for QB-180

















Reviews: