background image

6

PFG S

erieS

 7 G

aS

-

Fired

 W

ater

 B

oiler

 – U

niverSal

 C

ontrol

 S

yStemS

Part Number 550-110-643/0605

These boilers must have vent dampers:

 

• PFG 5 (U.S. only)

These boilers may have vent dampers:

 

• PFG 6-8 (U.S. only)

 

• PFG 5-7 (Canadian)

These boilers must not have vent damper:

 

• PFG 8 (Canadian)

If not installing damper, proceed to page 7.

1. 

  Once damper is installed on boiler, 

boiler  will  not  operate  without 

damper installed.

 

  Only dampers listed on page 16 are 

approved for use on PFG Series 6 &   

7 boilers. Any other damper installed 

can cause severe personal injury or 
death.

2.  Effikal and Johnson dampers - install plug (packed in damper 

carton of 4” thru 8” dampers) in hole in damper blade.

3.  Minimum clearances:

      PFG - 48” between jacket top and combustible ceiling.

 

  DO  NOT  modify  draft  hood  or 

damper, or make another connection 

between  draft  hood  and  damper 

or  boiler.  This  will  void  C.S.A. 

certification and will not be covered 

by  Weil-McLain  warranty.  Any 

changes will cause severe personal 
injury, death or substantial property 

damage.

4.   

PFG

 - Damper must  be  installed  directly  on  top  of  draft 

hood  so  that  it  serves  only  one  boiler  and  so  that  damper 

blade indicator is visible to homeowner. See Figure 1 or 2 

and Figure 3 or 4.

 

Where screws or rivets are used to secure damper to draft 

hood, they must not interfere with free movement of damper 

blade.

5.  Install damper harness between damper actuator and knock-

out  in  jacket  top  panel.    Use  strain  relief  connectors  and 

locknuts to secure both ends of damper harness.  See Figure 

1 or 2.

 

  Keep wiring harness clear of all hot 

surfaces.

6.  Remove dummy receptacle from damper plug in boiler wiring 

harness.  Plug damper harness receptacle into damper harness 

plug.  See Figure 1 or 2.

 

  Bypassing (jumpering) damper will 

cause flue products such as carbon 

monoxide to escape into house. This 

will cause severe personal injury or 
death.

 

  After  boiler  has  operated  once,  if 

either end of harness is disconnected, 

system shutdown will occur. Boiler 

will  not  operate  until  harness  is 
reconnected.

7.  Effikal damper - damper “Hold Open” switch must be in “Au-

tomatic Operation” position for system to operate properly.

8.  Apply label shown in step 5 to damper, so that it is visible 

after installation.

9.  Proceed to page 7.

Johnson Damper

Figure 4

Effikal Damper

Figure 3

Section B: Damper Installation

Summary of Contents for 7 PFG

















Reviews: