Weidmuller IE-WL-BL-AP-CL User Manual Download Page 43 | Manualshive

Page: 43 / 76

background image

Wi-Fi device IE-WL-BL-AP-CL

Web Console Configuration

3-43

are out of the control room for an extended period, they can still be informed of the status of devices almost
instantaneously when exceptions occur.

In addition to logging these events, the IE-WL-BL-AP-CL supports different approaches to warn engineers
automatically, such as SNMP trap and e-mail.

System Logs

System Log Event Types

All the event group types are shown on this page. Select the event types (groups) that you want to enable by
checking the

Enable logging

box next to the event types. By default, all event types are enabled (checked).

The system events log can be viewed at

Status



System Logs

.

System-related events

Event is triggered when…

System warm start

The IE-WL-BL-AP-CL is rebooted, such as when its settings are
changed (IP address, subnet mask, etc.).

System cold start

The IE-WL-BL-AP-CL is rebooted by power down.

Watchdog triggers reboot

The IE-WL-BL-AP-CL is rebooted by watchdog

Network-related events

Event is triggered when…

LAN link on

The LAN port is connected to a device or network.

LAN link off

The port is disconnected (e.g., the cable is pulled out, or the
opposing device shuts down).

Client joined/ left
(for AP/Master mode)

A wireless client is associated or disassociated.

WLAN connected to AP
(for Client/Slave mode)

The IE-WL-BL-AP-CL is associated with an AP.

WLAN disconnected
(for Client/Slave mode)

The IE-WL-BL-AP-CL is disassociated from an AP.

RSTP changed

The RSTP topology has changed

RSTP new root bridge ID

The RSTP changes its root bridge ID

Client Roaming from previous AP to
current AP (for Client/Slave mode)

A client roams from a previous AP to the current AP if the signal
strength of the current AP is greater than the previous AP by a
certain value.

IP address conflict

The IE-WL-BL-AP-CL has the same IP address as another device
connected to the same subnet.

Link fault pass-through LAN/WLAN
connected because of WLAN/LAN up

The WLAN/LAN link is up and the Link fault pass-through (LFPT)
enables the LAN/WLAN functionality.

Link fault pass-through LAN/WLAN
disconnected because of WLAN/LAN down

The WLAN/LAN link is down and the Link fault pass-through (LFPT)
disables the LAN/WLAN functionality.

Channel availability check over DFS
frequency (for AP/Master mode)

The channel availability check (CAC) is started on channel
[channel] at [frequency] GHz for 60 sec./
The channel availability check (CAC) task has been completed on
channel [channel] at [frequency] GHz./
A radar signal is detected on channel [channel] at [frequency]
GHz.

«
...
41
42
43
44
45
...
»

Summary of Contents for IE-WL-BL-AP-CL













































































Reviews:

No comments

Related manuals for IE-WL-BL-AP-CL

Brand: Panasonic Pages: 18

Brand: Panasonic Pages: 29

Brand: 3Com Pages: 6

Brand: Meru Networks Pages: 73

Brand: Firetide Pages: 32

Brand: Ruijie Networks Pages: 12

Brand: wikango Pages: 20

Brand: AzureWave Pages: 48

Brand: AmbiCom Pages: 1

Brand: AmbiCom Pages: 29

Brand: PHICOMM Pages: 64

Brand: HPE Pages: 4

iB-WRX300NP Baton

Brand: iBall Pages: 66

Pre-Paid Mobile Wi-Fi

Brand: Telstra Pages: 29

Edge Point EP-R8

Brand: Ubiquiti Pages: 36

Brand: Ubiquiti Pages: 44

WINDY31 WINDY31

Brand: SyNET Pages: 10

Brand: Benington Networks Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands