background image

 

- 9 - 

Cable Wiring

—Diagrams labeled “Cable Wiring” present standard cable 

wiring schemes for cables used to connect Ethernet Switch’s ports to other 
devices. These diagrams display three pieces of information: 

1.

 

When building your own cable, refer to the “pin-to-pin” Cable Wiring 
information displayed between the two vertical dashed lines to see 
which pin of the connector on the left should be connected to which pin 
of the connector on the right. 

2.

 

The information to the left of the left vertical dashed lines gives the 
pinouts of the relevant Ethernet Switch port. 

3.

 

The information to the right of the right vertical dashed line gives the 
pinouts of the opposing device’s port. 

 

NOTE

 

1.

 

The pin numbers for male DB9 and DB25 connectors, and 
hole numbers for female DB9 and DB25 connectors are 
labeled on the connector. However, the numbers are typically 
quite small, so you may need to use a magnifying glass to see 
the numbers clearly. 

2.

 

The pin numbers for both 8-pin and 10-pin RJ45 connectors 
(and ports) are typically not labeled on the connector (or port). 
Refer to the following Pinout and Cable Wiring diagrams to see 
how RJ45 pins are numbered   

RS-232 Connection 

IE-SW-PL16M Series has one RS-232 (10-pin RJ45) console port, located on 
the top panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable (see the 
cable following wiring diagrams) to connect IE-SW-PL16M Series console 
port to your PC’s COM port. You may then use a console terminal program, 
such as Windows Hyper Terminal, to access IE-SW-PL16M Series console 
configuration utility. 

RJ45 (10-pin) Console Port Pinouts 

Pin 

Description 

 

------ 

DSR 

------ 

GND 

TxD 

RxD 

GND 

------ 

DTR 

10 

------ 

 

 

 

 

 

Summary of Contents for IE-SW-PL16M Series
















Reviews: