background image

3

WARNING: 

To reduce the risk of serious injury, read the following important precautions

before using the home gym system.

1. It is the responsibility of the owner to ensure

that all users of the home gym system are
adequately informed of all precautions.

2. The home gym system is intended for home

use only. do not use the home gym system in
an commercial, rental, or institutional setting.

3. Read all instructions in this manual and in

the accompanying literature before using the
home gym system. 

4. Use the home gym system only on a level

surface. Cover the floor beneath the home
gym system for protection.

5. Inspect and tighten all parts often. Replace

any worn parts immediately. 

6. Keep children under the age of 12 and pets

away from the home gym system at all times.

7. Never release the press arm, butterfly arms,

military press arm, leg lever, leg press plate,
lat bar or nylon strap while weights are
raised. The weights will fall with great force. 

8. Keep hands and feet away from moving parts.

9. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-
ing down.

10. Always wear athletic shoes for foot protec-

tion.

11. Always stand on a foot plate when perform-

ing an exercise that could cause the home
gym system to tip.

12. Keep your hands away from the leg press

upright when the military press arm is being
used. Your hand could become pinched
between the leg press upright and military
press arm.

13. Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.

14. Always disconnect the lat bar from the home

gym system when performing an exercise
that does not use the lat bar.

IMPORTANT PRECAUTIONS

WARNING:

Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product. 

¥ Keep clear of
  this area.

The warning decals shown below and at the right have been placed on the
home gym system in the locations shown on page 4. If a decal is missing or
illegible, please call our Customer Hot Line at 1-800-999-3759 and order a
free replacement decal. Place the decal on the home gym system in the loca-
tion shown.

Warning Decal No. 2

Warning Decal No. 1

Summary of Contents for Club 16.4st


































Reviews: