ASSEMBLY
4
1
2
88
4
82
Bracket
Low Side
14
88
5
3
8
8
3
3
11
86
8
11
3
20
4
1
27
17
Before beginning assembly, carefully read the
following information and instructions:
• Place all parts of the CJXT3 in a cleared area
and remove the packing materials; do not dis-
pose of the packing materials until assembly is
completed.
• Read each assembly step before you begin.
• For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the centre of this manual.
Note: Some small parts may have been pre-
attached for shipping purposes. If a part is not in
the parts bag, check to see if it has been pre-
attached.
• As you assemble the CJXT3, be sure that all
parts are oriented as shown in the drawings.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
• Two (2) adjustable spanners
• One (1) standard screwdriver
• One (1) phillips screwdriver
• One (1) rubber mallet
• Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.
1.
Before you begin, make sure that you have
carefully read the instructions at the top of
this page.
Press a 2” Inner Cap (27) into the Base (4).
Attach the Pulley Plate (20) to the Base (4) with
two 5/16” x 2 3/4” Bolts (11), two 5/16” Flat
Washers (8), and two 5/16” Nylon Locknuts (3).
Insert the two 5/16” x 2 1/2” Carriage Bolts (1) up
through the Base (4).
2.
Press the two 2” Outer Caps (88) onto the
Stabiliser (5).
Insert two 5/16” x 2 3/4” Carriage Bolts (14) up
through the Stabiliser (5). Slide the end of the
Base (4) and the Rear Upright (82) onto the
Carriage Bolts. Make sure that the Rear Upright
is turned as shown. Thread 5/16” Nylon
Locknuts (3) onto the two Carriage Bolts. Do not
tighten the Nylon Locknuts yet.
Attach the Brace (86) to the Rear Upright (82)
and the Stabiliser (5) with two 5/16” x 2 3/4” Bolts
(11), two 5/16” Flat Washers (8), and two 5/16”
Nylon Locknuts (3). Do not tighten the Nylon
Locknuts yet.
WEIGHT RESISTANCE CHART
WEIGHT
PRESS ARM
BUTTERFLY ARM
LEG LEVER
HIGH PULLEY
LOW PULLEY
PLATES
(lbs.)
(lbs.)
(lbs.)
(lbs.)
(lbs.)
1
29
26
18
16
18
2
48
39
32
30
32
3
69
50
45
43
45
4
83
64
58
56
58
5
107
80
71
68
71
6
129
96
84
80
84
7
145
112
98
93
98
8
163
130
110
105
110
9
181
149
125
117
125
10
200
Do not use
134
128
134
Note: The actual resistance at each weight station may vary due to differences in individual weight plates, as
well as friction between the cables, pulleys, and weight guides.
(1 pound=0,454 kg.)
