background image

3

BEFORE YOU BEGIN

ASSEMBLED 
DIMENSIONS: 
Height: 191,5cm.
Width: 141,5cm.
Length: 183cm.

Foot Plate

Low Pulley Station

High Pulley Station

Lat Bar

Leg Lever

Arms

Stepper

Weight Stack

Backrest

Resistance Cylinders

VKR Arms

Weight Pin

18

Thank you for selecting the versatile WEIDER

®

CJXT3

Master Trainer. The CJXT3 offers a selection of weight
stations designed to develop every major muscle
group of the body. Whether your goal is to tone your
body, build dramatic muscle size and strength, or
improve your cardiovascular system, the CJXT3 will
help you to achieve the specific results you want.     

For your benefit, read this manual carefully before
using the WEIDER

®

CJXT3. If you have additional

questions, please call our Customer Service
Department at 0345-089009. To help us assist you,
please note the product model number and serial
number before calling. The model number is
WESY700921. The serial number can be found on a
decal attached to the CJXT3 (see the front cover of
this user's manual).

Before reading further, please review the drawing
below and familiarise yourself with the parts that are

TROUBLE-SHOOTING AND MAINTENANCE 

Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The
weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

TIGHTENING THE CABLES

Woven cable, the type of cable used on the weight
system, can stretch slightly when it is first used. If
there is slack in the cables before resistance is felt,
the cables should be tightened. Locate the adjust-
ment sleeve and adjustment screw near the lower
end of the Short Cable (23). Loosen the adjustment
screw. Pull the end of the Short Cable until there is no
slack. Slide the adjustment sleeve and the ball against
the indicated 3 1/2” Pulley (15). Retighten the adjust-
ment screw. Make sure that the cables are not too
tight, or the top weight will be lifted off the weight
stack.

Additional slack can be removed by locating the indi-
cated 5/16” Nylon Locknut (3) near the upper end of
the Front Upright (42). To tighten the cables, hold the
5/16” x 3” Bolt (17) and turn the Nylon Locknut clock-
wise. 

Note: If a cable tends to slip off the pulleys often, the cable may have become twisted. Remove the cable
and re-install it.

If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

23

15

15

Adjustment
Screw

Adjustment
Sleeve

Ball

23

35

3

42

Summary of Contents for CJXT3
















Reviews: