Weider 8700 I User Manual Download Page 6

Page: 6 / 32

The Four Stages of the Assembly Process
Frame Assembly

—You will begin by assembling

the base and the uprights that form the skeleton of

the weight system.

Arm Assembly

—During this stage you will

assemble the arms and the leg lever.

Cable Assembly

—During this stage you will attach

the cables and pulleys that connect the arms to the

weights.

Seat Assembly

—During the final stage you will

assemble the seat and the backrest.

• Assembly requires two persons.

• Because of its weight and size, assemble the

weight system in the location where it will be

used. Make sure that there is enough clearance

to walk around the weight system.

• Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until you complete all assembly steps.

• To identify small parts, see page 5.

• In addition to the included tool(s), assembly

requires the following tools:

one Phillips screwdriver

one standard screwdriver

one rubber mallet

two adjustable wrenches

Assembly may be easier if you have a set of

wrenches. To avoid damaging parts, do not use

power tools.

ASSEMBLY

Summary of Contents for 8700 I

































Search results

Summary of Contents for 8700 I

Reviews:

Related manuals for 8700 I

Brands by name

Popular brands

Weider 8700 I, User Manual

Search results

Summary of Contents for 8700 I

Reviews:

Related manuals for 8700 I

Brands by name

Popular brands