Weider 8700 I User Manual Download

Page: 3 / 32

IMPORTANT PRECAUTIONS

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or per-

sons with pre-existing health problems.

2. Use the weight system only as described in

this manual.

3. It is the responsibility of the owner to ensure

that all users of the weight system are

adequately informed of all precautions.

4. The weight system is intended for home use

only. Do not use the weight system in a com-

mercial, rental, or institutional setting.

5. Use the weight system only on a level sur-

face. Cover the floor beneath the weight

system to protect the floor.

6. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

7. Keep children under age 12 and pets away

from the weight system at all times.

8. The weight system should not be used by

persons weighing more than 300 lbs.

(136 kg).

9. Wear appropriate exercise clothes while

exercising; do not wear loose clothes

that could become caught on the weight

system. Always wear athletic shoes for foot

protection.

10. Keep hands and feet away from moving

parts.

11. Always secure the weight stack with the lock

pin and the lock after exercising to prevent

unauthorized use of the weight system (see

LOCKING THE WEIGHT STACK on page 23).

12. Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you

are exercising, stop immediately and make

sure that the cables are on the pulleys.

13. Always stand on the foot plate when per-

forming an exercise that could cause the

weight system to tip.

14. Never release the arms, leg lever, lat bar, or

handle strap while weights are raised. The

weights will fall with great force.

15. Always disconnect the lat bar from the

weight system when performing an exercise

that does not require the lat bar.

16. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

WARNING:

To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your weight system before using your weight

system. ICON assumes no responsibility for personal injury or property damage sustained by or

through the use of this product.

Summary of Contents for 8700 I

































Search results

Summary of Contents for 8700 I

Reviews:

Related manuals for 8700 I

Brands by name

Popular brands

Weider 8700 I, User Manual

Search results

Summary of Contents for 8700 I

Reviews:

Related manuals for 8700 I

Brands by name

Popular brands