10
09
GB
GB
Avoid cutting your lawn when it is wet. Wet grass
tends to form clumps and interferes with the mulching
action. The best time to mow your lawn is the early
afternoon. At this time the grass has dried and the
newly cut area will not be exposed to the direct sun.
biodegrade quickly to provide nutrients for the lawn.
Always mulch with your highest engine (blade) speed,
as this will provide the best re-cutting action of the
blades.
height so that the lawn mower cuts off only the top
one-third of the grass blades. If the lawn is overgrown
it will be necessary to raise the height of cut to reduce
pushing effort and to keep from overloading the engine
and leaving clumps of mulched grass. For extremely
heavy mulching, reduce your width of cut by over-
lapping previously cut path and mow slowly.
For best results, adjust the lawn mower cutting
Certain types of grass and grass conditions may
require that an area be mulched a second time to
completely hide the clippings. When doing a second
cut, mow across or perpendicular to the first cut path.
Change your cutting pattern from week to week.
Mow north to south one week then change to east to
west the next week. This will help prevent matting and
graining of the lawn.
1
Change more often when operating under a heavy
load or in high ambient temperatures.
2
Service more often when operating in dirty or dusty
conditions.
3
Replace blades more often when mowing in sandy
soil.
GENERAL RECOMMENDATIONS
The warranty on this lawn mower does not cover items
that have been subjected to operate or abuse or negli-
gence. To receive full value from the warranty, operator
must maintain mower as instructed in this manual.
Some adjustments will need to be made periodically
to properly maintain your unit.All adjustments in the
Service and Adjustments section of this manual should
be checked at least once each season.
Replace Air Filter Paper
Cartridge
E
N
G
I
N
E
Check Engine Oil Level
Change Engine Oil
Clean Air Filter
Inspect Muffler
Clean or replace Spark
Plug
2
1
2
MAINTENANCE SCHEDULE
CUSTOMER RESPONSIBILITIES
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
Check for loose fasteners
Clean/Inspect Grass
Catcher (If Equipped)
Clean Lawnmower
Clean Under Drive
Cover (Power-
Propelled Mowers)
M
O
W
E
R
Check/Sharpen/
Replace Blade
BEFORE
EACH USE
AFTER
EACH USE
EVERY 25HOURS
OR EVERY SEASON
3
EVERY
10 HOURS
BEFORE
STORAAGE
SERVICE
DATES
Lubrication Chart
l
Once a year, replace the spark plug, clean or replace
air filter element and check blade for wear. A new
spark plug and clean/new air filter element assures
proper air-fuel mixture and helps your engine run
better and last longer.
l
Follow the maintenance schedule in this manual.
WARNING: MAKE SURE DOING ALL
OPERATIONS WHEN THE ENGINE
STOPPED.
disc
TO SHARPEN BLADE
NOTE:
We do not recommend sharpening blade but
if you do, be sure the blade is balanced.
Care should be taken to keep the blade balanced.An
unbalanced blade will cause eventual damage to lawn
mower or engine.
The blade can be sharpened with a file or on a
grinding wheel. Do not attempt to sharpen while on
the mower.
To check blade balance, drive a nail into a beam
or wall. Leave about one inch of the straight nail
exposed. Place center hole of blade over the head
of the nail. If blade is balanced, it should remain in
a horizontal position. If either ends of the blade moves
downward, sharpen the heavy end until the blade is
balanced.
NOTE:
Remove the blade adapter and check the
key inside hub of blade adapter. The key must be in
good condition to work properly. Replace adapter if
damaged.
TO REPLACE BLADE
1.Position the blade adapter on the engine cranks
haft. Be sure key in adapter and crankshaft keyway
are aligned.
2.Be sure the trailing edge of blade(opposite sharp
edge) is up toward the engine.
3.Install the blade bolt with the Belleville spring into
blade adapter and crankshaft.
4.Use block of wood between blade and lawn mower
housing and tighten the blade bolt, turning clockwise.
IMPORTANT:
BLADE BOLT IS GRADE
10.9 HEAT TREATED.
place wire where it cannot come in contact with spark
plug.
2.Turn lawn mower on its side. Make sure air filter
and carburetor are up.
3.Use a woodblock between blade and mower hou-
singto prevent blade from turning when removing
blade bolt.
NOTE:
Protect your hands with gloves and/or wrap
blade with heavy cloth.
4.Remove blade bolt by turning counter-clockwise.
5.Remove blade and attaching hardware.
BLADE CARE
For best results, mower blade must be kept sharp.
Replace bent or damaged blades.
TO REMOVE BLADE
1.Disconnect spark plug wire from spark plug and
chemicals which can harm rubber.
Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
BEFORE EACH USE
1
Check engine oil level.
2
Check for loose fasteners.
LUBRICATION
Keep unit well lubricated.
LAWN MOWER
Always observe safety rules when performing any
maintenance.
TIRE
Keep tires free of gasoline, oil, or insect control
Fig.13
Clutch
Screw
Central bolt
Screw
Blade
Spring washer
Spacer
Woodruff key
Screw
Spacer
Shield
Bracket 1
Bracket 2
Bracket 3
Spacer
Models with BBC
Standard models
