WEG CFW300 V1.3X, Programming Manual

Page: 105 / 157

Digital and Analog Inputs and Outputs
CFW300 | 12-13
12
Table 12.6: Digital input functions
Value Description Dependence
0 Not used -
1 Run/Stop command P224 = 1 or P227 = 1
2 General Enable command -
3 Fast Stop P224 = 1 or P227 = 1
4 Forward run command
(P224 = 1 and P223 = 4) or
(P227 = 1 and P226 = 4)
5 Reverse run command P224 = 1 or P227 = 1
6 Start command P224 = 1 or P227 = 1
7 Stop command P224 = 1 or P227 = 1
8 Forward Rotation Direction P223 = 4 or P226 = 4
9 Local/Remote selection P220 = 4
10 JOG command
(P224 =1 and P225 = 2) or
(P227 =1 and P228 = 2)
11 Electronic Potentiometer: Accelerate E.P. P221 = 7 or P222 = 7
12 Electronic Potentiometer: Decelerate E.P. P221 = 7 or P222 = 7
13 Multispeed reference P221 = 8 or P222 = 8
14 2
nd
Ramp selection P105 = 2
15 to 17 Not used -
18 No external alarm -
19 No external fault -
20 Fault reset Active fault
21 to 23 Not used -
24 Disable flying start P320 = 1 or 2
25 Not used -
26 Lock Prog. -
27 to 31 Not used -
32 Multispeed reference with 2
nd
Ramp (P221 = 8 or P222 = 8) and P105 = 2
33 Electronic Potentiometer: Accelerates E.P. with 2
nd
Ramp (P221 = 7 or P222 = 7) and P105 = 2
34 Electronic Potentiometer: Decelerates E.P. with 2
nd
Ramp (P221 = 7 or P222 = 7) and P105 = 2
35 Forward run with 2
nd
Ramp
(P224 = 1 and P223 = 4) or
(P227 = 1 and P226 = 4) and P105 = 2
36 Reverse run with 2
nd
Ramp
(P224 = 1 and P223 = 4) or
(P227 = 1 and P226 = 4) and P105 = 2
37 Accelerates E.P./Start
P224 = 1 or P227 = 1
P221 = 7 or P222 = 7
38 Decelerates E.P./ Stop
P224 = 1 or P227 = 1
P221 = 7 or P222 = 7
39 Stop command P224 = 1 or P227 = 1
40 Safety switch command P224 = 1 or P227 = 1
41 Application Function 1 -
42 Application Function 2 -
43 Application Function 3 -
44 Application Function 4 -
45 Application Function 5 -
46 Application Function 6 -
47 Application Function 7 -
48 Application Function 8 -
49 Activate Fire Mode
(*)
50 Manual/Automatic PID (Only DI2 for P903 = 1)
(*)
51 Increase Setpoint Command (PE) (Only DI3 for P903 = 1)
(*)
52 Decrease Setpoint Command (Only DI4 for P903 = 1)
(*)
53 1st DI Control Setpoint (Only DI3 for P903 = 1)
(*)
54 2st DI Control Setpoint (Only DI4 for P903 = 1)
(*)
(*) For further details refer the Chapter 18 APPLICATIONS on page 18-1 .