3
S
Stop engine and allow to cool before re-
moving fuel cap.
S
Always store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAFETY
WARNING:
Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage trimmer head and be thrown
causing serious injury.
S
Use only for trimming, mowing, edging and
sweeping. Do not use for pruning or hedge
trimming.
S
Keep firm footing and balance. Do not over-
reach.
S
Keep all parts of your body away from spin-
ning line and muffler. Keep engine below
waist level. A hot muffler can cause serious
burns.
S
Cutting with the line on left side of the shield
will throw debris away from the operator.
S
Use only in daylight or good artificial light.
TRANSPORTING AND STORAGE
S
Allow the engine to cool; secure unit before
storing or transporting in vehicle.
S
Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
S
Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S
Store unit so line limiter blade cannot acci-
dentally cause injury. Unit can be hung by
the tube.
S
Store the unit out of the reach of children.
SAFETY NOTICE:
Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings.
Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti-vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE:
This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many
internal
combustion
engines
be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by your Au-
thorized Service Dealer.
ASSEMBLY
WARNING:
Make sure your unit is
properly assembled and all fasteners are se-
cure.
ATTACHING THE HANDLE
Groove
S
Assemble handle to the unit as shown;
make sure bottom of handle is seated in the
groove in the trigger housing.
NOTE:
Wing nut must be assembled on the
side of the unit opposite the operator’s position.
S
Pivot handle to a comfortable position.
Tighten handle securely.
ATTACHING THE SHIELD
WARNING:
The shield must be prop-
erly installed.
The shield provides partial
protection from the risk of thrown objects to
the operator and others and is equipped with
a line limiter blade which cuts excess line to
the proper length. The line limiter blade (on
underside of shield) is sharp and can cut you.
S
Remove wing nut from shield.
S
Insert bracket into slot as shown.
S
Pivot shield until bolt passes through hole
in bracket.
S
Securely tighten wing nut onto bolt.
Slot
Shield
Wing
Nut
Bracket
Line Limiter Blade
