%%
F84EFG4G<BA
<:A<G<BAHF4:8
6
3
7
5
1
4
2
The grill illustrated may have slight
differences than the model purchased.
2
6
D
DANGER
When the “excess gas flow control” feature is activated,
a small amount of gas is still flowing to the burners. After
turning off the cylinder and burner control knobs, wait at
least 5 minutes for the gas to clear before attempting to light
the grill. Failure to do so may result in an explosive flare-up,
which can cause serious bodily injury or death.
C) Turn the cylinder on by turning the cylinder valve counterclockwise
(3)
.
D
WARNING: Do not lean over the open barbecue.
% *HOJUFFBDIBEKBDFOU4FBS4UBUJPO
®
main burner
(4)
. Push the control knob in and
turn to START/HI until you hear the igniter snap - continue to hold control knob in
for two seconds. This action will spark the igniter, the burner lighting tube and then
main burner.
E) Check that the burner is lit by looking through the cooking grates
(5)
. You should
see a flame. If burner does not light on first try, push control knob in and turn to OFF.
Repeat lighting procedure a second time.
Sear Station
®
Burner Lighting: Ignition By An Adjacent Ignited Main Burner
F) Turn Sear Station
®
burner control knob to the ON position
(6)
.
G) Verify burner ignition by visual inspection of a flame
(7)
.
D
WARNING: If ignition does not occur in 5 seconds, turn
burner control OFF, wait 5 minutes, and repeat steps F &
G, or see “SEAR STATION
®
BURNER MANUAL IGNITION”
instructions.
D
WARNING: If the burner still does not light, turn the burner
control knob to OFF and wait 5 minutes to let the gas clear
before you try again or try to light with a match.
Note: See “MAINTENANCE” for burner removal and cleaning
procedure.
X
TO EXTINGUISH
Push in and turn each burner control knob clockwise to OFF position. Turn gas supply off
at the source.
X
SEAR STATION
®
BURNER IGNITION
Summary lighting instructions are inside the left hand cabinet door.
D
DANGER
Failure to open the lid while igniting the barbecue’s burners,
or not waiting 5 minutes to allow the gas to clear if the
barbecue does not light, may result in an explosive flare-up
which can cause serious bodily injury or death.
The Sear Station
®
burner has an on or off control setting. To ignite the Sear Station
®
CVSOFSZPVNVTUGJSTUJHOJUFUIFUXPBEKBDFOUNBJOCVSOFST
Adjacent Main Burner Snap Ignition
Note: Each main burner control knob snap igniter creates a spark from the igniter
electrode to the burner lighting tube. You generate the energy for the spark by pushing
in the control knob and turning to START/HI. This will ignite each individual burner.
D
WARNING: Check hose before each use of barbecue for
nicks, cracking, abrasions or cuts. If the hose is found to
be damaged in any way, do not use the barbecue. Replace
using only Weber
®
authorized replacement hose. Contact
the Customer Service Representative in your area using the
contact information on our web site.
Log onto www.weber.com
®
.
A) Open the lid
(1)
.
B) Make sure all burner control knobs are turned off
(2)
. (Push control knob in and turn
clockwise to ensure that it is in the OFF position.)
D
WARNING: The burner control knobs must be in the OFF
position before turning on the liquid propane cylinder tank
valve. If they are not in the OFF position, when you turn on
the LP cylinder valve, the “excess gas flow control” feature
will activate, limiting the flow of gas from the LP cylinder. If
this should occur, turn off the LP cylinder valve and burner
control knobs. Start over.
ARRÊTÉ
APAGADO
OFF
ON
