background image

8

Check package contents

The following item will be found in the top box.

Bottom rack

The following items will be found in the large box
(shipper).

CharBin Storage 
Container

Bowl assembly

Lid Assembly

Ash catcher assembly

Two Char-Basket Fuel Holders

LP tank 

Tools needed:

Phillips screwdriver

7/16 inch and 7/8 inch or an adjustable wrench

Pliers

Hammer

Block of wood

Supplies needed

Your LP tank is shipped empty for safety.

You will

need to fill it (See Step "Fill LP tank").

You will need a soap and water solution to check for gas
leaks.

Packages

Your Weber Performer Grill comes in a large box
(shipper) which includes a top box, and bottom carton.

There is a hardware pack of small parts and hardware
that will be found in the bottom carton.

Note - The hardware size of nuts, bolts and screws is
given. For example "1/4-20 x 1/2 inch bolt" means a bolt
1/4 inch in diameter with 20 threads to the inch, 1/2 inch
long. On a small screw, "8-18 x 5/8 inch screw" means a
number 8 screw, with 18 threads to the inch, 5/8 inch
long.

While we give much attention to our products,
unfortunately an occasional error may occur. If a part
is missing, do not go back to the store. Call the Weber
Customer Service Center toll free 

1-800-446-1071

to

receive immediate assistance. Have your owner’s
manual and serial number available for reference.

Summary of Contents for Performer Touch-N-Go





























Reviews: