background image

35

1

Lid (assembly)

2

Lid handle

3

Warm-Up Basket

4

Warming rack 

5

Short Flavorizer bars (8)

6

Long Flavorizer bars (5)

7

Cooking grates (2)

8

Work table

9

Tubing plugs (3)

10 1/4-20 x 2 inch bolts (5)
11 Spacer bracket
12 End bracket
13 Left frame 
14 Condiment basket
15 1/4-20 x 1/2 inch bolts (6) 
16 1/4 inch nylon washers (7) 
17 Side panel (2)
18 Side frame (2)
19 Bottom tray 
20 Catch pan holder 
21 Catch pan 
22 Drip pans (2) 
23 Accessory rack 
24 Base panel
25 Tool holders (3) 
26 Front panel 
27 Plastic buttons (10)

Parts List

All items are single quantities unless otherwise specified.

Parts can be ordered directly from Weber-Stephen
Products Company by phone or mail.

Note - Do not return parts to Weber-Stephen Products Co.
without first contacting the Customer Service Center by
phone or mail. Returning the part may not be necessary.

28 Hair pin cotters (2) 
29 Hinge pins (2) 
30 Thermometer 
31 1/4-20 keps nut 
32 Cooking box 
33 Burner control knobs (3) 
34 Control panel 
35 Igniter button 
36 Phillips screws/washers (2) 
37 Crossover tube 
38 Front and back burners (2) 
39 Center burner 
40 1/4-20 stainless steel wing nuts (2) 
41 Spider Stopper Guards (3)
42 Manifold assembly 
43 Manifold bracket 
44 Igniter 
45 Igniter lock nut 
46 Gas catcher ignition chamber 
47 Igniter wire (black) 
48 Igniter wire (white) 
49 Right frame 
50 Gas supply line
51 Flare fitting
52 Control panel inserts (2)

WARNING:

Use only Weber factory authorized parts. The
use of any part that is not factory authorized
can be dangerous. This will also void your
warranty.

While we give much attention to our products,
unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-800-446-1071 to
receive immediate assistance. Have your owner’s manual
and serial number of the barbecue available for reference.

Weber-Stephen Products Company
Customer Service Center
250 South Hicks Road
Palatine, IL  60067-6241
(800) 446-1071

Summary of Contents for GENESIS GENESIS 1500 LX





































Reviews: