manualshive.com logo in svg

Weber 41995, Owner'S Manual

Share
Download
Weber 41995 Owner'S Manual Download Page 48

D-15

Rotisserie Troubleshooting

Problem

Check

Cure

Burner does not light.

Did you hold the burner control
knob down and hold down for 20
seconds until after burner ignited?

Try to relight burner by holding
burner control knob down and
continue holding down until 20
seconds after burner has ignited.

Is the igniter sparking?

Replace battery in igniter button
module.
Reseat burner ring.

Burner does not light or burner
has a small flickering flame.

The excess flow safety device,
which is part of the grill to cylinder
connection, may have activated.

Too reset the excess flow safety
device turn all burner control knobs
and  the cylinder valve OFF.
Disconnect the regulator from the
cylinder. Turn burner control knobs
to HIGH. Wait at least 1 minute. Turn
burner control knobs OFF.
Reconnect the regulator to the
cylinder. Turn cylinder valve on
slowly. Refer to “Lighting
Instructions”

If problems cannot be corrected by using these methods, please contact the Customer
Service Representative in your region using the contact information sheet provided with
your manual.

Summary of Contents for 41995





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands