background image

4

This operating and maintenance manual is designed to help 

you become familiar with your soil compactor and enable you 

to maintain it and use it for its intended purpose.

The safety and maintenance instructions provided in this 

manual will help avoid hazards, reduce repair and downtime 

costs and will increase the reliability and operational readiness 

of your machine. Follow these instructions precisely.

This operating and maintenance manual must always be kept 

at the implementation site of the machine and be available to 

the machine operator.

Enclosed with this manual is a valid declaration of conformity 

and a spare parts lists for orders of spare parts. Store these 

documents carefully. 

If you require any additional information, turn to your 

Weber MT dealer. 

Found on the last page of this manual is a QR code. Scan 

it to acquire the current contact addresses of all Weber MT 

branches.

You can obtain information on the assembled Hatz diesel 

engine and the associated operating and maintenance manual 

as well as the spare parts list, if needed, at  

www.hatz-diesel.com

1. Introduction

Summary of Contents for 0116621

































Reviews: