background image

PAGE 

IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT US TOLL-FREE AT .800.456.7865

24-0245 REV. A 07/06

8320
8332
8342   
8352

8380
8381
8383
8384
8390
8393

8385
8391 
8394
8395

8345
8957
8958
8959

Parts List

2

2

2

2

A    Floor Mounting Brackets

0

0

2

0

B    Center Supports

8

12

12

0

C    Shelf Dividers

2

2

2

2

D    End Panels

2

3

3

0

E    Shelves

#32-0162

#32-0162

#32-0163

#32-0183

           Bolt Kit

INSTALLATION MANUAL

JUMBO VAN SHELVING

ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.

Approximate Assembly and Installation Time:  

60-80 min. (1 to 1.3 hours) depending on number of shelf  
units and van equipment installation experience.

TOOLS REQUIRED 

• Electric Drill 
• Drill Bits: 13/32", 5/16", 1/8" 
• Open End Wrenches: (2) 7/16", 9/16"  
• 1" Hole Saw

Danger  of  explosion.  Do  not  use  this  product  for  storing  or 
transporting  flammables,  explosives,  hazardous  materials,  or 
hazardous waste, such as containers of gasoline, solvents, gun 
powder,  dynamite,  propane  tanks,  acetylene  tanks  and  cutting 
torches. This product is only intended and safe for use in storing 
and transporting small tools, equipment and other similar materials. 
Any  modifications  made  to,  or  unintended  use  of  this  product, 
could create a hazardous condition that can cause death, serious 
personal injury or property damage.

These instructions are to be followed using the parts and fasteners 
supplied  for  proper  installation.  Any  modifications  or  improper 
installation of this product will create a hazardous condition that 
can cause property damage, serious personal injury or death.

        DANGER

– NOTICE –

        WARNING

Any modification or unintended use of this product shall immediately 
void all manufacturers warranties. Manufacturer disclaims all liability 
for injuries to persons or property resulting from any modification 
to, or unintended use of this product.

A

C

D

A

D

E

E

E

B

Summary of Contents for JUMBO VAN SHELVING







Reviews: