We 26110110240 0 Series User Manual Download Page 16 | Manualshive

Page: 16 / 41

We 26110110240 0 Series User Manual Download Page 16

WIRELESS CONNECTIVITY & SENSORS

Evaluation board user manual

CON3

nRF52840

Function

1

GND

2

P0.09

NFC1

3

P0.10

NFC2

4

GND

3.3.4 CON4

Connector CON4 (SMA receptacle) is used to connect an external antenna. The 2.4GHz
antenna Himalia-2600130021 shall be used.

CON4

Function

Inner

RF signal

Outer

GND

The board supports 50

Ω

connection by just soldering/unsoldering one component to use either

module’s internal PCB antenna or to connect an external antenna.

In order to use the external antenna for long range tests, Capacitor C6 has
to be populated with a 22pF capacitor

and C28 should be left

unpopulated.

Figure 5: Capacitor connection to external antenna

In order to use the internal PCB antenna of the module, C28 has to be popu-
lated with a 22pF capacitor

and C6 should be left unpopulated.

3.3.5 CON5

Connector CON5 is used to connect the WE Sensor evaluation boards. This feature is sub-
jected to a customized firmware and not supported by default firmware.

Thyone-I, Proteus-III(-SPI), Setebos-I

14

Version 1.5, May 2023

www.we-online.com/wcs

«
...
14
15
16
17
18
...
»

Summary of Contents for 26110110240 0 Series










































Reviews:

No comments