background image

NE Pumps.

 

3

 

 

 

2.  Safety Recommendations.

 

 

 

Wastewater pumps NE, NE 4 and NE 6 are not recommended 
for use in pools or water recreation facilities.  

 

WDM pumps are designed to operate safely when used and 
maintained according to this manual. 

 

Rotating parts of the pumps are dangerous and can cause 
injury. Operators and maintenance personnel should be 
aware of and follow safety recommendations. 

 

The pumps are considered heavy equipment. Handle them 
with care. 

 

Pumps should not pump hazardous material unless they have 
been designed and designated to do so.  

 

The pipes and pump should never be forced to fit if using the 
correct size. If you have to apply force, then get a different 
size. 

 

To reduce the risk of electrical shock, all wiring of pumps, 
motors, overload protection and control panels must be in 
accordance with the National Electric Code (NEC) or the 
Canadian Electrical Code (CEC) and all applicable state, 
province, local codes and ordinances. Requirements will vary 
depending on usage and location. Improper grounding will 
void the warranty. 

 

To reduce the risk of electrical shock, always disconnect the 
pump from the power source before handling or servicing. 
Cable should be inspected frequently. 

 

Never handle connected power cords with wet hands.  

 

If any product is to be returned, it must be cleaned, sanitized, 
or decontaminated as necessary according to any applicable 
laws and regulations prior to shipment, to protect employees 
from exposure to health hazards. 

 

Always wear eye protection when working on pumps. 

 

Loose fitting clothing can easily be caught by the impeller or 
other moving parts, therefore do not wear loose fitting clothing 
when doing maintenance or service work on the pump. 

 

Gloves should be worn whenever handling parts that have 
sharp edges. 

 

Wear safety shoes when handling heavy parts or tools. 

 

For any maintenance always disconnect power.

 

 

Never place hands in the  suction or discharge openings.

 

 

Safety handles should always be fastened securely before 

Summary of Contents for NE Series





























Reviews: