manualshive.com logo in svg

WCS Dumpsters FEL 4, Assembly Instructions Manual

Share
Download
WCS Dumpsters FEL 4 Assembly Instructions Manual Download Page 10

10 

 

Version 2: August 4, 2020 

Waste Container Systems

 

 

Installing the Bag with 4 Support Rods and Rails 

Step 14

 - Place bag in dumpster with front side with four flaps facing the front. 

 NEED NEW PHOTO 

 

 
Step 15

- Slide bottom end bag support rail through bag sleeve on each end and attach rail to back corner posts using 

bottom bolt. Tighten.  
 
 

 
 
 
 
 
 
 
 
 
 
 
Step 15A

 

–

 Slide top end bag support rails through bag sleeve and attach rail to outside of front corner posts. Top hole 

on each corner. 

Finger Tighten Only. Rail will be attached by the bag rod to the back corner posts in a later step. 

 

 
 

 
 

 
 
 
 
 
 
 
 
 
 

 
NOTE 

–

 The three shorter rods are for the bag. The longer rod is for the lids.  

 
Step 16

 - Insert front bottom bag support rod from left or right bottom front post bottom hole 

through bag sleeve, center vertical supports, bag sleeve, to opposite corner.  Insert cotter pin in end 
of rod to secure. 
 
Repeat Step 16 for the Bottom Rear Bag Support Rod.  
 
Need photos.  

 
 
 
 
 

Summary of Contents for Dumpsters FEL 4













Reviews:

No comments

Brands by name

Popular brands

Load more brands