manualshive.com logo in svg

WCS Dumpsters FEL 4, Assembly Instructions Manual

Share
Download
WCS Dumpsters FEL 4 Assembly Instructions Manual Download Page 1

1 

 

Version 2: August 4, 2020 

Waste Container Systems

 

 

Assembly Instructions for WCS Dumpsters 

FEL 4 Yard Containers  

Tools Needed 

•

 

Impact Driver, Drill, or Ratchet (Make sure that your battery is fully charged as a weak battery can result in 
inadequate tightening of bolts.) 

•

 

Socket –9/16 and 11/16 

•

 

Hammer – Use to seat bolts in case coating is interfering.  

•

 

Screwdriver 

Note: The dumpster can be assembled on the floor, but the use of a sturdy table for assembly in an elevated position 
makes the job easier. Can be assembled by one person. 

When assembly is complete 

make sure all bolts are fully tightened before use.

 

Orientation of Dumpster

 – Front is determined by the locking left front wheel and the front left and right vertical corner 

posts are lower than the back.  

Parts List 

Parts Packed in Dumpster 

5- bag and lid support rods (longest rod is used for the top, back bag support.) 
1 - lid support rod 
1 - left front vertical support 

 

1- center front vertical Support 
1 - right front vertical support 
1 - back right vertical support 
1 - back left vertical support 
2- top end bag support rails (Concave Bars) 
2- bottom end bag support rails (Flat bars) 
2 - bag protectors 
1 - Front panel  
2 - Lids 

Hardware Bag 

5- cotter pins  
18- 1-inch bolts 
18- nuts  
 
Attached to Dumpster When Shipped 
2 - left and right lid brackets (Shown at Right) 
1 - middle lid bracket (Shown at Right) 
2 – Front Corner “L” Brackets 
 
 
 
 
 
 

Summary of Contents for Dumpsters FEL 4













Reviews:

No comments

Brands by name

Popular brands

Load more brands