manualshive.com logo in svg

WCS Dumpster, Assembly Instructions Manual

Share
Download
WCS Dumpster Assembly Instructions Manual Download Page 7

7 

 

Version 6: June 6, 2019 

Waste Container Systems

 

 

Step 10

 – Take off left and right front hinge nuts only leave bolt in place. 

Install front panel

 by placing inside front 

bottom rail of frame and over the hinge bolts. Replace hinge nuts 

Finger Tighten Only

. 

 

 

 

 

 

 

 

 

 

 

 

Step 11

 - Attach left and right support rails to front rail forming a letter 

“V”

 using 4 bolts/nuts. 

Finger tighten only. 

Make sure that bag support rod holes are facing up. Finger Tighten Only. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step 12

 - Install bag protection shields. Left and right front top corners. Bolts go through bag protection shields, corner 

post, and front panel. Attach nuts. 

Finger tighten only.

 These secure front panel. Tighten all 10 bolts securing front of 

dumpster components.  

 

Step 13

 - Attach end bag support rails for bags to each front corner post. Rails go inside of corner posts. 

Finger Tighten 

Only. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bag Support 

Rod Holes  

Remove nut only and 

place the front panel 

over the hinge bolts to 

secure it to the frame.  

Front view location of hinge bolt.  

Summary of Contents for Dumpster











Reviews:

No comments

Brands by name

Popular brands

Load more brands