wibenchmfg.com
507 E. Grant St. Thorp, WI 54771 • P - 800.242.2303
Specifications are subject to change. Product
images are for illustrative purposes only and may
differ from the actual product.
12
iXchange® Wall
Assembly Instructions
SSW0802-AL
Care & Maintenance
Whiteboard Surfaces
General Guidelines
The manufacturing of the whiteboard recommends solvent-
based dry-erase markers, instead of water-based or “low
odor” dry eraser markets. Low-odor markers take longer to
dry and ink pigments cling more aggressively leaving behind
a residue or the appearance of ghosting. The manufacturer
recommends SPRAYWAY foaming glass cleaner (aerosol or
whips), yellow
micro fiber cloths and white lint free polishing cloths.
Avoid using foam erasers to avoid pigment transformation.
Daily Care and Cleaning
1. Wipe surface with a clean Yellow micro fiber cloth.
2.If writing has remained on surface for more than 48 hours,
a yellow micro fiber cloth moistened with warm water can be
used.
3. Wipe dry with a white lint free polishing cloth.
Weekly or as Needed Cleaning
1. Remove all papers and magnetic attachments from board.
2. Wipe complete surface with yellow micro fiber cloth.
3. Apply SPRAYWAY foaming cleaner and work foam into
surface with fingers on ghosting areas.
4.Rinse with yellow micro fiber cloth moistened with warm
water.
5.Dry with white lint free polishing cloth.
Special Cleaning
To remove crayon, transparent tape residue and other
miscellaneous stains dampen a clean cloth with water and
sprinkle a small amount of powder cleanser on the cloth.
Begin cleaning a small area with a back and forth horizontal
motion using normal pressure as if cleaning a window.
Wipe off the residues with a dry cloth then rinse with clear
water. Wipe dry with a clean, dry cloth. Repeat if necessary.
Permanent Marker Cleaning
It is recommended not to use permanent marker on the
whiteboard. If permanent marker is accidentally applied to
whiteboard surface, moisten a clean, dry cloth with isopropyl
alcohol. Begin cleaning in a circular motion to loosen marker
residue. Dry with a clean, dry cloth. (If isopropyl alcohol is not
available try writing over the permanent ink marker with a dry
erase marker then wipe with a clean, dry cloth.) Repeat as
often as necessary to remove all residues.
Cabinet Hardware
Door and Drawer Pulls/Handles:
Pulls/Handles can easily be cleaned with a damp cloth or
sponge and a mild soap or detergent, or all purpose cleaners.
Acidic or abrasive cleaners can damage the finish; do not use
them. Drain cleaners containing lye may permanently damage
the finish.
If you spill a drain cleaner, wipe it up immediately and rinse
several times with water.
Periodically check the screw fasteners and tighten if
necessary. Do not over-tighten as it may damage the door or
drawer,
or crack the pull/handle itself.
Hinges:
Hinges can easily be cleaned with a damp cloth or sponge and
a mild soap or detergent, or all purpose cleaners.
For heavily soiled hinges, mild abrasive cleansers, like Comet
or Ajax, can be useful for cleaning heavily soiled hinges, but
take precaution to not scratch the finish. A better alternative
is to remove the hinges from the door and soak them in a mild
soap or detergent solution, using a toothbrush to get hard to
reach areas if necessary. When reattaching the hinges to the
door, a drop of glue in the screw hole is recommended.
After time, hinges may start to squeak. These noises do not
affect the performance of the hinges but they can become
a nuisance. Periodically spray WD-40 at each joint along the
pin so it soaks into the center, being careful not to spray the
laminate door finish as it may stain.
If the doors have a European (concealed) hinge, periodic
adjustment may be required to keep the doors aligned and
working properly. A separate document is available that
explains this process. If you need this document, or require
assistance, contact Wisconsin Bench Manufacturing at
(800) 242-2303.
Drawer Slides:
Periodically clean with a soft damp cloth. Ball-bearing slides
are lubricated with grease to ensure smooth quiet operation
and long life. Avoid removal of this grease during cleaning.
