Wayne PC4 Operating Instructions Manual Download Page 3

www.waynepumps.com

PC4

3

MAINTENANCE

 

Let pump cool for at least 20 minutes before 

  attempting to service. Motor MAY be extremely 

hot. Personal injury MAY result.

1.   Pump should be checked periodically for proper operation.

 

ALWAYS disconnect the electrical supply before 

  attempting to operate, service, or perform any 

maintenance. If the power source is out of sight, lock and tag in the open 

(off) position to prevent unexpected power application. Failure to do so 

WILL result in fatal electrical shock. Only qualified electricians SHOULD 

repair this unit. Improper repair WILL result in fatal electrical shock.

BRUSH REPLACEMENT

 

Brushes for this pump SHOULD be inspected 

  after 100 hours of operation. 

Pumps with excess of 100 hours of operation may stop operating 
or fail to start. This could be due to worn brushes or carbon build-
up. The brushes should be removed and carbon removed. Worn 
brushes are not covered under warranty. Replacement brushes may 
be available from WAYNE Pumps. Call 1-800-237-0987 to order.
1)    Disconnect electrical cord from power supply.
2)    Remove brush caps with screwdriver.
3)    Remove old brush assembly.
4)    Replace brushes, make sure springs do not pinch during 

assembly. Align/center tabs on the back of the brush spring 
with the flats on the brush hlder. REF. fig3.

5)    Replace brush caps.
For other problems, consult troubleshooting chart.

NOTES

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

Summary of Contents for PC4

















Reviews: