manualshive.com logo in svg

Wayne-Dalton TORQUEMASTER 5140, Installation Instructions And Owner'S Manual

Share
Download
Wayne-Dalton TORQUEMASTER 5140 Installation Instructions And Owner'S Manual Download Page 24

Tools Needed:

24

Please Do Not Return This Product To The Store. 

Contact your local Wayne-Dalton dealer. 

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at 

www.wayne-dalton.com

Positioning Support bracket

23

usING a TaPE MEasuRE, MaINTaIN aN Equal MEasuREMENT “x”

(TOP OF DOOR TO BOTTOM OF TORquEMasTER® TuBE) aT BOTh

ENDs aND ThE CENTER.

TOP sECTION

“x”

“x”

NOTE:

 see idrive

®

 main installation and 

owners manual for idrive

®

 parts.

NOTE:

 idrive

®

 must be installed on a 

solid mounting surface.

locate the mounting surface. Remove 
(2) 1/4”-20 flange nuts from bottom of 
opener. 

NOTE: 

Do not discard flange nuts. 

 Place the support bracket underneath 
opener, to the right side of motor, 
centered on mounting surface. using a 
tape measure, level the bottom of the 
TorqueMaster

®

 spring tube to the top of 

the door section with the idrive

®

 resting 

on the support bracket. Once 
TorqueMaster

®

 spring tube is level, drill 

1/8” pilot holes for the lag screws. Then 
secure support bracket to the mounting 
surface with (2) 1/4” x 1-1/2" lag 
screws.

IMPORTANT:

 TORquEMasTER

®

 sPRING 

TuBE MusT BE lEVEl aFTER suPPORT 
BRaCkET Is FasTENED TO MOuNTING 
suRFaCE.

NOTE:

 If wood mounting surface is 

behind dry wall, use 1/4” x 2” lag 
screws.

lift and slide the opener over the 
support bracket, aligning the mounting 
studs with the bracket slots. loosely 
fasten to mounting studs with the (2) 
1/4”-20 flange nuts.

NOTE:

 Do not tighten 1/4”-20 flange  

nuts to opener studs at this time. you 
will be instructed when to tighten them 
in the idrive

®

 main installation and 

owners manual.

 Remove the temporary orange label 
holding the antenna wire. straighten 
antenna wire and angle it 45 degrees to 
the right. 

NOTE:

 Do not coil the antenna wire. 

This will reduce the radio signal range.

 

Power Drill

1/8” Drill Bit

7/16” socket 

Driver

45 aNGlE

aNTENNa 

WIRE

MOuNTING 

suRFaCE

(hEaDER)

TOP OF DOOR

suPPORT 

BRaCkET

1/4” x 1-1/2” 

laG  sCREWs

1/4” - 20 

FlaNGE NuTs

MOuNTING 

sTuDs

MOuNTING 

sTuDs

BRaCkET 

slOTs

suPPORT 

BRaCkET

TORquEMasTER

®

 

sPRING TuBE

(2) 1/4” - 20 

FlaNGE NuTs

TORquEMasTER

®

 

sPRING TuBE

“x”

Summary of Contents for TORQUEMASTER 5140







































Reviews:

No comments

Brands by name

Popular brands

Load more brands