manualshive.com logo in svg

Wayne-Dalton TORQUEMASTER 5140, Installation Instructions And Owner'S Manual

Share
Download
Wayne-Dalton TORQUEMASTER 5140 Installation Instructions And Owner'S Manual Download Page 19

19

Tools Needed:

Tools Needed:

Please Do Not Return This Product To The Store. 

Contact your local Wayne-Dalton dealer. 

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at 

www.wayne-dalton.com

INST

All

ATION

TorqueMaster

®

 Spring Tube

TorqueMaster

®

 springs come lubricated 

and pre-assembled inside the 
TorqueMaster

® 

spring tube. To install, lay 

the TorqueMaster

®

 spring tube on the 

floor (inside garage) in front of the door 
with the labeled end to the left.

laBElED END

TORquEMasTER

®

 

sPRING TuBE

None

15

16

Center bracket bushing 

NOTE: 

If you are installing the 

i

drive

®

 

opener on your garage door, skip this 
step and continue with step 17.

NOTE: 

If you are not installing an 

i

drive

®

 

opener on your garage door, you must 
install the center bracket bushing 
assembly. Follow these instructions for 
non-

i

drive

®

 operated garage doors. 

NOTE:

 If you are installing a 

DoorMaster

™

 opener, see optional 

DoorMaster

™

 Bracket installations on 

page 31, Figure a.

Being cam shaped the center bracket 
bushing only fits one way. 
slide the center bracket assembly 
towards the center of the TorqueMaster

®

 

spring tube, from the right side as 
shown.

NOTE:

 upon completion of this step, 

continue with step 18.

CENTER 

BRaCkET 

assEMBly

 TORquEMasTER

®

 

sPRING TuBE

 TORquEMasTER

®

 

sPRING TuBE

CENTER

BRaCkET

BushING

None

Summary of Contents for TORQUEMASTER 5140







































Reviews:

No comments

Brands by name

Popular brands

Load more brands