Wayne-Dalton 8700, Quick Start Manual, Page: 4 / 18

4
A. FLAG ANGLES (AS REQUIRED):
A1. Fully Adjustable (F.A.) Flag Angles
B. JAMB BRACKETS (AS REQUIRED):
B1. Fully Adjustable (F.A.) Jamb Brackets
C. TRACK ROLLERS (AS REQUIRED):
C1. Short Stem Track Rollers / C2. Long Stem Track Rollers
D. GRADUATED END HINGES:
D1. Single Graduated End Hinges (S.E.H.), Industry Standard
D2. Single Graduated Center Hinges (S.E.H.), Narrow Hinges
D3. Double Graduated End Hinges (D.E.H.), Industry Standard
E. STACKED SECTIONS:
E1. Top Section / E2. Intermediate(s) Section
E3. Lock Section / E4. Bottom Section
F. TOP FIXTURES:
F1. Top Fixtures
G. STRUT(S) (AS REQUIRED):
G1. Struts (U-shaped)
H. DRAWBAR OPERATOR BRACKET (FOR TROLLEY OPERATED DOORS):
H1. Top Halve Drawbar Operator Bracket (As Required)
H2. Bottom Halve Drawbar Operator Bracket (As Required)
H3. Drawbar Operator Bracket (Supplied By Others) (As Required)
I. TRACKS (AS REQUIRED):
I1. Left Hand and Right Hand Horizontal Track Assembly
I2. Left Hand and Right Hand Vertical Tracks
I3. Left Hand and Right Hand Riveted Vertical Track Assembly
I4. Left Hand and Right Hand Angle Mount Vertical Track Assembly
J. TORSION SPRING ASSEMBLY (AS REQUIRED):
J1. Left Hand and Right Hand Torsion Springs (As Required)
J2. Counterbalance Lift Cables
J3. Left Hand and Right Hand End Bearing Brackets (As Required)
J4. Left Hand and Right Hand Cable Drums
J5. Center Bracket (As Required)
J6. Center Bracket Bushing (As Required)
J7. Center Bearing Bracket (As Required)
J8. Torsion Shaft / Torsion Keyed Shaft (As Required)
J9. Torsion Keyed Shafts (As Required)
J10. Keys (As Required)
J11. Center Coupler Assembly (As Required)
J12. Set Collars (As Required)
K. REAR BACK HANGS (AS REQUIRED):
K1. Left Hand and Right Hand Back Hang Assemblies
K2. - K3. Left Hand and Right Hand Rear Center Back Hang Assemblies
L. BOTTOM CORNER BRACKETS (AS REQUIRED):
L1. Left Hand and Right Hand Bottom Corner Brackets
M. BOTTOM WEATHER SEAL (AS REQUIRED):
M1. Bottom Weather Seal (Door Width)
N. TRACK ROLLER CARRIER’S (AS REQUIRED):
N1. Track Roller Carrier’s
NOTE: The illustrations shown on this page are general
representations of the door parts. Each specific door
models may have unique variations.
C1.
C1.
F1.
F1.
B1.
B1.
I2.
I2.
I3.
J5.
J1.
J3.
J1.
J8.
I4.
J4.
J3.
J4.
J10.
J12.
J5.
J9.
J9.
I1.
J11.
A1.
I3.
J7.
J7.
J6.
J10.
J10.
J10.
J12.
M1.
L1.
L1.
J2.
N1.
N1.
I1.
K1.
I4.
G1.
H2.
H1.
H3.
NOTE: For Item (K2), The Rear Center Back Hang
Assemblies are to used for all doors over 11’0” door
height and over 14’0” door width. One Rear Center
Back Hang Assembly, per side.
NOTE: For Item (K3), The Rear Center Back Hang
Assemblies are to used for all doors over 16’0” door
height. Two Rear Center Back Hang Assemblies, per
side.
K2.
K3.
E4.
E1.
E2.
E3.
K1.
K2.
D2.
D1.
C1.
C2.
D3.
J2.
A1.
BREAKDOWN OF PARTS