background image

Optional Accessories

Your WayCool

®

Evaporative cooler can be purchased with accessories/options or some of these options can be retrofitted to your

WayCool

®

after the initial purchase. Necessary instructions are included with all equipment purchased separate from your WayCool

®

.

Accessories or Options available at time of purchase only:

Manual Fill and Water Level Gauge

Oscillating air duct

Accessories or Options available at time of purchase or after purchase:

Pneumatic Wheel 

Automatic Shutoff 

Water Conditioner & Cleaner

Manual Fill & Water Gauge

Pneumatic Wheel Option

Manual Fill is an option that must be specified at
the time of purchase. This option includes a water 
level gauge. The Manual Fill option allows you to 
Manually fill the WayCool

®

without having to take out

the grates or pads. The gauge allows you to monitor
the water level to avoid running the pump dry.

Pneumatic wheels are available at the time of your WayCool

®

purchase or as a retrofit kit on a

previously purchased WayCool

®

.

The pneumatic wheel options includes two locking and two non-locking wheels.

Pneumatic wheels are designed to allow for easy rolling on rough or uneven surfaces.

Fill pipe and cap

Water gauge

WC-1HPMF.20 - Manual fill

15

WayCool

®

Water Conditioner & Cleaner

WayCool

®

Water

Condition is
recommended to control
odors found to be
present in some water
sources.

•  Place the tab under 

the float valve water 
outlet for quick, fast 
odor control.

•  Place the tab next to 

the pump for longer 
lasting and more 
constant odor control.

WayCool

®

Cleaner is recommended to remove scale

buildup from the water supply system.

• Clean 

WayCool

®

according to the instructions on 

page 13 of this manual.

Refill with water and add one (1) pint of Cooler 
Cleaner Treatment to the water reservoir.

• Operate 

the 

WayCool

®

in the "pump only" mode 

for approximately 20 minutes.

•  Drain, clean and refill the WayCool

®

with fresh 

water.

•  Repeat treatment steps if deemed necessary.
• Operate 

WayCool

®

in normal manner and repeat 

treatment when evidence of scale build up 
begins.

Summary of Contents for 1HP - Series






















Reviews: