WayCool 1HP MFA Series User Manual Download Page 5

5

Safety Recommendations

PLEASE NOTE

Minimum inlet pressure is 10 PSI; maximum inlet pressure is 100 PSI.

Never leave unit unattended while in operation.

READ AND SAVE THESE INSTRUCTIONS!

This is an electric device with moving components. There is the possibility of fire, electric shock or
injury to persons. Ensure all the safety recommendations are adhered to in order to minimize this risk.

• Disconnect all power and unplug the unit before you inspect, clean or perform maintenance on the 

components of the unit.

• Never reach into the unit when it is running; you could become entrapped by the V-belt or injured by the 

rotating fan blades.

• The metal frame edges are sharp; don't run your hand along them. Be careful and wear gloves when you 

reach under the frame to inspect the PVC pipes and mesh socks.

• A GFCI (Ground Fault Circuit Interrupter) is recommended for use with this product.

• If pads and grates are removed for servicing, they must be replaced prior to operating the unit.

Specifications

Height and Width 

33" x 33" wide x 54" high 

(with casters and directional spout)

Shipping Weight 

225 pounds

Blower 

double-inlet centrifugal

Motor 

1 HP, 115V, 2 speed, 60 Hz 

(also available in 230V and 50 Hz)

Pump Filter 

washable polyethylene filter

Pump Discharge Filter 

480 micron stainless steel

Reservoir Capacity 

24 gallons

Pump 

submersible vane type, 280 gallons per hour

Housing 

high impact ABS plastic with UV protection

Evaporation Media

chemically treated cellulose paper

Optional Water Supply 

standard 3/4" hose connection (garden hose size)

Component Overview

Actual WayCool® may
vary slightly from unit
shown here.

Summary of Contents for 1HP MFA Series



















Reviews: