© 2020
8
PLD10000/PLD12500 LASER DIODE DRIVER
INSTALL THE PLD ON THE PLD10EV BOARD
Align the pins of the PLD with the plated holes on the
evaluation board, making sure all pins are aligned before
seating the PLD on the board.
!
v
erify
ThaT
The
pLD
is
properLy
orienTeD
on
The
boarD
,
wiTh
p
in
1
aT
The
correcT
LocaTion
. r
efer
To
Next, insert the two 4-40 x ¼” screws through the tabs on
the PLD and into the threaded inserts on the PCB; then
tighten. Finally, solder the PLD pins to the PLD10EV board.
It is essential to mechanically secure the PLD to the circuit
board with the 4-40 x ¼” screws. The electrical pins alone
do not provide sufficient mechanical strength to secure the
PLD to the circuit board.
CONFIGURE THE PLD10EV BOARD FOR
YOUR APPLICATION
If you are using the PLD10EV evaluation board to familiarize
yourself with operating the PLD10000 or PLD12500, follow
these instructions to configure the jumpers on the evaluation
• Laser Type-Select Jumper
. Remove this jumper for
Type A/B laser operation. Install the jumper to tie pin 3
to pin 23 for Type C laser operation. The factory default
configuration is with the jumper removed.
• LD Power Supply Jumper.
To operate the PLD and
laser from a single 5 VDC power supply, install this
jumper. If you are operating a high-compliance laser
with a separate power supply, remove the jumper. The
jumper must be removed when using the PLD12500.
The factory default configuration is with the jumper
installed.
(GND)
VCC
(GND)
-
+
Connector
AUX VCC
-
+
VCC
NC
PD ANODE
PD CATHODE
ANALOG INPUT
I MONITOR
COMMON MON(-)
LIM I MONITOR
LIM I STATUS
LD ENABLE
PD AUX
AUX V+
P MONITOR
LD +5V SUPPLY JUMPER
MONITOR-
LIM I MON
POWER
LASER CONNECT
LDC
LD SUPPLY
LDA/
OUT
PD AUX
LASER DISABLE
LASER ENABLE
I MONITOR
P MONITOR
PLD10EV-00600-A REV B
POWER
ON
ON
OFF
1
S3
S2
S1
R2
JP2
JP1
J4
J2
J1
D1
J3
P
L
I
H
PLD10000
Laser Diode Driver
MODE
H
OUT
LIM I
PD RNG
ENBL
OUT
ADJ
LIM I
ADJ
Output
Current
DISABLE
ENABLE
Monitor
Select
PD CURRENT
LD CURRENT
Test Points
Power
ON
OFF
Power
LED
Laser Connection
Use 14 AWG minimum
CA
THODE
ANODE
Laser Type-C Jumper
Install ONLY for Type-C Lasers,
Shown here for Type A/B Lasers
Power Supply Input
Use 14 AWG minimum
Power Supply Shorting Bar
Install jumpter to tie +5 V pins (13,14,15)
to +LD Supply pins (7,8,9).
Screw Lock Connectors
Use 22 AWG minimum
Power Supply Input
Pads for custom
connector installation
C2
Figure 5. PLD10EV Evaluation Board
WIRE THE PLD LASER DRIVER
for wiring instructions specific to your
configuration. For setup and configuration use a test load.
The same wiring instructions apply whether the PLD is
used on the PLD10EV board or installed on a custom circuit
board.
Table 3.
Wiring Configurations
CONFIGURATION
DIAGRAM
Type A & B Laser Diode,
Single 5 VDC Power Supply
Type A & B Laser Diode,
High-Compliance Laser Diode
Type A & B Laser Diode,
Negative Supply Operation
Type C Laser Diode,
Single Power Supply