background image

the device is switched off, remove the 3 screws around the unit, pull on the 
radome (be careful to do it vertically to protect the probe inside) and then pull 
on the probe connector (not the tube) to remove it. Then attach a different 
probe and close the radome.

4. 

POWER SUPPLY (SMART POWER)

MonitEM-Lab

 is equipped with an intelligent controller that allows it to supply 

the main board and detect its working mode to make a reset in case of an 
emergency.

 Important: 

Always disconnect the device from the mains before 

manipulating it, since some internal parts may be hazardous.

4.1 AC power supply

The device is powered directly from an external power connection. A regulator 
transforms 110- 240V AC (50-60Hz) into 12V DC.

4.2 

USB mode

This power supply mode can only be used to change the parameters of the 
device. The USB powers the microprocessor and the SD card so that it can 
read and change the device’s data. It is not a normal operating mode. It can be 
very useful as an initial connection, since in this mode the device will not make 
connection to the server and will allow adjustment of all the desired values 
before starting up in normal mode.

Note:

 if the USB is connected before or just after the 

MonitEM-Lab

 is connected to 

a power supply, the system will start in USB mode, since the power supply controller 

takes 2–3 seconds to power up the device. To get back in normal mode you can press 

the restart button of the software or completely switch off the unit.

 

User’s Manual

Electromagnetic Radiation Monitoring Device MonitEM-Lab   

P. 

7

Summary of Contents for MonitEM-Lab





























Reviews: