PAGE 2
PAGE 3
Min.
2in
Lock
Unlock
F
G
H
A
B
C
D
E
Adjust
Height
Press
Down
Adjust
Height
Drip Loop
GFCI
ONLY
Electronic ballast
Hangers
Lock Nut
GFCI Plug
Paradynamic
Reflector
ON/OFF
Switch
8.5in x 11in
8.5in x 11in
WAVE POINT®
T5 4 Lamp Retrofit Kit
(4 Row Lamp Configuration)
Includes: 2 Sun Wave
®
and 2 Superblue 460
®
lamps
MODEL #
DESCRIPTION
DIMENSION (W x H x L) (Approx.)
01019
96 watt 24in T5 4 Lamp Retrofit Kit
8.125in x 2.25in x 23.8125in
01020
156 watt 36in T5 4 Lamp Retrofit Kit
8.125in x 2.25in x 34.675in
01021
216 watt 48in T5 4 Lamp Retrofit Kit
8.125in x 2.25in x 46.50in
PART LIST
1.
14X light amplifying paradynamic reflector
2. GFCI plug
3. 2 Sun Wave
®
and 2 Superblue 460
®
HO T5 lamps
4. ON/OFF switch
5. Lock nut
6. Hanger
7. Electronic ballast
Read and follow the guidelines to ensure the proper
use and application. Failure to follow these guidelines
may result in Retrofit Kit damage, electrical shock,
fire and/or injury.
1. Use this product for its intended use only.
2. Never yank or pull the cord from the electrical outlet.
3.
Do not place the Retrofit Kit directly on top of the aquarium.
4. Do not operate if the plug or wire is damaged.
5.
The Retrofit Kit is not to come in contact with water.
6.
The Retrofit Kit must be turned off/disconnected from the power
supply before any maintenance is done to either the Retrofit Kit or
the aquarium.
7. Verify that hands are dry prior to disconnecting the power.
8. To reduce the risk of electrocution keep all connections dry.
9.
If the Retrokit Kit falls or comes in contact with water/excess
moisture, unplug the Retrofit Kit from the power supply immediately
before removing. Failure to do so may cause electrical shock or
injury.
10.
The Retrofit Kit and connections need to be free of water, moisture
and salt build up at all times. Failure to do so will cause electrical
arching resulting in possible fire or electrical shock.
11.
Do not place above an open top aquarium.
INSTRUCTIONS FOR INSTALLATION
NOTE:
•
Only place in well ventilated canopy. This Retrofit Kit is intended to be above the aquarium. Do not place directly on
top of any aquarium without using hangers or canopy mounting bracket. Do not place above the aquarium without a
glass top.
•
Use and/or consult a professional electrician or general contractor for installation
INSTALL TO THE CEILING
ER
Additional hardware and tools required:
Anchors, drill and a screwdriver.
1.
Undo lock nut. (A)
2.
Locate a wood beam in the ceiling. Using the mounting
brackets drill 2 pilot holes in the intended locations.
Secure directly to the wood beam. (B)
NOTE: If using anchors to secure in the mounting
brackets and light Retrofit Kit. Use and follow the
directions provided with the anchors. If there are
any questions or concerns consult a professional
electrician or general contractor.
3.
Adjust the length of the cable. Cut off or hide
excess cable. Secure the end of the cable with the
cable stop. (C)
4.
Lock the lock nut. (D)
5.
Slide mounting bracket onto the track (E). Position
them equal distance from the edge. Slide bracket in a
minimum of 2in from the edge of the track. (F)
Note: Unit must be disconnected from the power.
6.
To level the Retrofit Kit adjust hanging wire to the
desired height by pressing the wire outlet in and
sliding cable in and out. (G)
7.
Connect power supply cord to the Retrofit Kit.
8.
Plug directly to a GFCI outlet.
IMPORTANT WARNING AND SAFEGUARDS
This product may contain chemicals known to the state
of California to cause cancer and or birth defects or other
reproductive harm. Wash your hand after handling this
product.
It is your sole responsibilities to verify that the plug and the
receptacle are clean and free of moisture and salt build up at
all times. The receptacle must be free of water, salt, calcium,
magnesium and dust. Failure to do so can cause fire, damage
to property, permanent damage to the product and personal
injury not limited to loss of life.
Do not plug into extension cord/power strip.
Hg lamp contains Mercury
Manage in accordance with disposal laws
See: www.lamprecycle.org
A drip loop must be used when
plugging all electrical aquarium
devices. A drip loop is that part of the
cord hanging below the receptacle.
The national code requires that a
GFCI (Ground fault circuit interrupter)
be used in the branch circuit
supplying all power to water pumps
and electrical aquarium equipment.
If you do not have a GFCI, have
an electrician install one prior to
operating any aquarium component.
