wattstopper intelliswitch TS-400-24 Installation Instructions Manual Download Page 5

TROUBLESHOOTING

Lights will not turn on:

1.   Verify that the ground wire is tightly secured.
2.  If lights still do not go on, call 800.879.8585 for technical support.

Lights will not turn off:

1.  Do the lights turn off when you press the 

ON

/

OFF

 button?

  •   If yes, check that the time-out period is set to the correct time-out. If the time-out 

period is adjusted to maximum, the lights will remain on for 12 hours.

  •  If no, call 800.879.8585 for technical support.

 

2.   To test if the unit is operating properly, set the time-out period to minimum. Lights 

should turn off after five minutes.

3.  If lights still do not turn off, call 800.879.8585 for technical support. 

Re-adjusting the Time-out Period:

To re-adjust the time-out period, set the new time delay in the user settings. If this is done 
while the timer is counting down a prior setting, the new setting will not be recognized until 
the present countdown has expired or the timer is turned 

OFF

 and 

ON

 again.

Questions/Unsure?:

Call 800.879.8585 for Technical Support.

CAUTION

TURN OFF THE POWER AT THE CIRCUIT BREAKER 

BEFORE WORKING WITH HIGH VOLTAGE

Call 800.879.8585 for Technical Support

Summary of Contents for intelliswitch TS-400-24







Reviews: