background image

Installation, Operation  
and Maintenance Manual

Series PWSYS-WH-SOFT-PRO-SE - 30K - 90K
Water Softener Systems

IOM-WQ-PWSYS-SOFT-PRO-SE

Important

Please read the entire manual before proceeding with the  

installation and startup. Your failure to follow any attached 

instructions or operating parameters may lead to the product’s 

failure.
Save manual for future reference

Refer to enclosed for operating parameters to ensure proper use 

with your water supply.

Table of Contents 

Pages

Important Safety Information – Read All . . . . . . . . . . . . . . . . . . . . . . . 2
Softener Anatomy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Control Start-up Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Service  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Softener Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Water Softener System Parts List  . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PWSYS-SOFT-PRO-SE

PURE WATER

Note:

 Do not use with water that is microbiologically unsafe or 

of unknown quality without adequate disinfection before or after 

the system. 

Summary of Contents for PWSYS-WH-SOFT-PRO-SE - 30K













Reviews: