6
STEP 7
Reverse Osmosis Module Mounting
Step A –
Determine best location for the
RO module to be mounted to
allow for future system main-
tenance . The parts bag has 2
self-tapping screws . Using an
electric drill with a Phillips bit,
screw them into the cabinet
wall 6" apart and 16" from the
bottom of the cabinet .
Note: Do not cut any RO system tubes at this time.
Drain Saddle Installation
Drain Saddle fits standard 1¼" – 1½" drain pipes
Note: The drain saddle must be mounted
at least 1½" above the nut of the P-trap or
crossbar from the garbage disposal to en-
sure proper drainage. If a second sink drain
is available, install it above the crossbar on
the second drain. Using Phillips screwdriver,
tighten screws evenly and securely on both
sides of the drain saddle. Keep the plastic
compression nut off at this time.
Caution: Do not overtighten the screws, it
may crack the drain saddle.
Gather the pieces of the drain saddle
1 Black compression nut
1 Semicircle bracket with opening
2 Screws
1 Foam gasket
2 Nuts for screws
1 Semicircle bracket
The small square black foam gasket with a circle cut out of the
middle must be applied to the inside of the drain saddle .
Remove sticky tape backing and stick to the drain saddle as shown .
STEP 4
Drill Hole and Connect
3
⁄
8
" Black Tube
from Faucet to the Drain Saddle
IMPORTANT: The black
3
⁄
8
" drain tube must be as SHORT and
STRAIGHT as possible to the drain saddle, making a downward
slope from faucet to drain saddle to allow for proper drainage.
This is a gravity fed line and if there is any bend or dip in the
tube, the rinse water will not flow into the drain properly. Water
may back up and come out the air gap hole in the back of the
faucet.
Step A –
With the drain saddle secured
onto the drain pipe, using a
1
⁄
4
"
drill bit installed in your electric
drill, insert the drill bit through
the opening in the drain saddle
and drill through the drain pipe .
Caution: It is very important to keep the drill centered to pre-
vent damage of the drain saddle while drilling.
Step B –
Measure the
3
⁄
8
" black tube
from faucet to the drain saddle
on the drain pipe and make
a straight cut to the correct
length .
Step C –
Slip black tube through black
compression nut . Insert black
tube into the opening in the
drain saddle and hand tighten the black nut, and add
1
⁄
4
turn with a wrench .
STEP 5
STEP 6
Green Tube Connection
Step A –
Locate green tube attached to the
RO Module . Insert the open end of
the green
1
⁄
4
" tube into the open
1
⁄
4
"
Quick-Connect fitting on the Adapt-
A-Valve™ making sure the tube is
pushed in all the way to the tube
stop .
Step B –
Connect the green tube from the RO
module to the Adapt-A-Valve™ that
is connected to the angle stop valve .
Leave enough tube so it is not kinked and cut the tube to
the desired length .
STEP 8
Red
1
⁄
4
" Tube Connection
(from Faucet to RO Module)
Step A –
Determine where the
1
⁄
4
" red tubing from the faucet and the
open end of the
1
⁄
4
" quick connect fitting (located on the
left side of the RO module) would join together comfortably.
Cut the red tube to length, making sure the cut is straight
and square . Insert the red tube into the open end of the
1
⁄
4
"
quick connect fitting making sure the tube is pushed in all
the way to the tube stop .
Connect
Red Tube
