background image

Installation, Operation  
and Maintenance Manual

Model PWSCAB30K
Water Softeners

IOM-WQ-PWSCAB30K

Important

Please read the entire manual before proceeding with the  

installation and startup. Your failure to follow any attached 

instructions or operating parameters may lead to the product’s 

failure.
Save manual for future reference

Refer to enclosed for operating parameters to ensure proper use 

with your water supply.

Table of Contents 

Pages

How To Get the Maximum Efficiency From Your Appliance  . . . . . . . . . 2
Checklist Before Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Do’s and Don’ts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Reference Illustrations   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Installation and Start-Up Procedures  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setting the Controller    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parts Diagrams   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Softener Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Warranty Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

PWSCAB30K

PURE WATER

Note:

 Do not use with water that is microbiologically unsafe or 

of unknown quality without adequate disinfection before or after 

the system. 

Summary of Contents for PWSCAB30K Pure Water





















Reviews: