Watts PVI Aqua Solve Family, Installation Manual

Page: 8 / 16

10
Programming the Water Softener
UP button
DOWN button
Low Salt
LED Indicator
Display
SELECT / MENU button FIG. 16 RECHARGE button
FIG. 18
When the transformer is plugged into the electrical
outlet, a model code and a test number (example:
J2.0), begin to flash in the faceplate display (See
Figure 17). Then, “12:00” and the words “SET TIME"
begin to flash.
NOTE: If “- - - -” shows in the display, press the
p
UP
or
q
DOWN button until the model code (See
table below) shows in the display. Then,
press the SELECT / MENU button to set, and
change to the flashing “SET TIME" display.
A. SET PRESENT TIME OF DAY
If the words “SET TIME" do not show in the display,
press the SELECT / MENU button a few times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
present time. Up moves the display ahead; down
sets the time back.
FIG. 19
B. SET WATER HARDNESS NUMBER
If you completed the previous step, the words “SET
HARDNESS" should show in the display. Otherwise,
press the SELECT / MENU button several times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
hardness of your water supply, in grains per gallon.
The default is 25. See table below for other units.
2 . When finished setting your water’s hardness num-
ber, press the SELECT / MENU button, and the dis-
play will change to show the “Set Recharge Time”
screen.
FIG. 17
NOTE: Press buttons and quickly release to slowly
advance the display. Hold the buttons down
for fast advance.
2 . When the correct time is displayed, press the
SELECT / MENU button, and the display will
change to show the “Hardness” screen.
Model Code
RBS-9ED SR9
RBS-14ED Sr14
RBS-
24ED
S
R24
10
Programming the Water Softener
UP button
DOWN button
Low Salt
LED Indicator
Display
SELECT / MENU button FIG. 16 RECHARGE button
FIG. 18
When the transformer is plugged into the electrical
outlet, a model code and a test number (example:
J2.0), begin to flash in the faceplate display (See
Figure 17). Then, “12:00” and the words “SET TIME"
begin to flash.
NOTE: If “- - - -” shows in the display, press the
p
UP
or
q
DOWN button until the model code (See
table below) shows in the display. Then,
press the SELECT / MENU button to set, and
change to the flashing “SET TIME" display.
A. SET PRESENT TIME OF DAY
If the words “SET TIME" do not show in the display,
press the SELECT / MENU button a few times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
present time. Up moves the display ahead; down
sets the time back.
FIG. 19
B. SET WATER HARDNESS NUMBER
If you completed the previous step, the words “SET
HARDNESS" should show in the display. Otherwise,
press the SELECT / MENU button several times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
hardness of your water supply, in grains per gallon.
The default is 25. See table below for other units.
2 . When finished setting your water’s hardness num-
ber, press the SELECT / MENU button, and the dis-
play will change to show the “Set Recharge Time”
screen.
FIG. 17
NOTE: Press buttons and quickly release to slowly
advance the display. Hold the buttons down
for fast advance.
2 . When the correct time is displayed, press the
SELECT / MENU button, and the display will
change to show the “Hardness” screen.
Model Code
RBS-9ED SR9
RBS-14ED Sr14
RBS-
24ED
S
R24
10
Programming the Water Softener
UP button
DOWN button
Low Salt
LED Indicator
Display
SELECT / MENU button FIG. 16 RECHARGE button
FIG. 18
When the transformer is plugged into the electrical
outlet, a model code and a test number (example:
J2.0), begin to flash in the faceplate display (See
Figure 17). Then, “12:00” and the words “SET TIME"
begin to flash.
NOTE: If “- - - -” shows in the display, press the
p
UP
or
q
DOWN button until the model code (See
table below) shows in the display. Then,
press the SELECT / MENU button to set, and
change to the flashing “SET TIME" display.
A. SET PRESENT TIME OF DAY
If the words “SET TIME" do not show in the display,
press the SELECT / MENU button a few times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
present time. Up moves the display ahead; down
sets the time back.
FIG. 19
B. SET WATER HARDNESS NUMBER
If you completed the previous step, the words “SET
HARDNESS" should show in the display. Otherwise,
press the SELECT / MENU button several times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
hardness of your water supply, in grains per gallon.
The default is 25. See table below for other units.
2 . When finished setting your water’s hardness num-
ber, press the SELECT / MENU button, and the dis-
play will change to show the “Set Recharge Time”
screen.
FIG. 17
NOTE: Press buttons and quickly release to slowly
advance the display. Hold the buttons down
for fast advance.
2 . When the correct time is displayed, press the
SELECT / MENU button, and the display will
change to show the “Hardness” screen.
Model Code
RBS-9ED SR9
RBS-14ED Sr14
RBS-
24ED
S
R24
When the transformer is plugged into the electrical
outlet, a model code and a test number (example:
J2.0), begin to flash in the faceplate display (See
Figure 17). Then, “12:00” and the words “SET TIME”
begin to flash.
NOTE: If “- - - -” shows in the display, press the UP
or DOWN button until the model code (See
table below) shows in the display. Then,
press the SELECT/MENU button to set, and
change to the flashing “SET TIME” display.
A. SET PRESENT TIME OF DAY
If the words “SET TIME” do not show in the display,
press the SELECT/MENU button a few times until
they do.
1. Press the UP or DOWN buttons to set the
present time. Up moves the display ahead; down
sets the time back.
B. SET WATER HARDNESS NUMBER
If you completed the previous step, the words “SET
HARDNESS” should show in the display. Otherwise,
press the SELECT/MENU button several times until
they do.
10
Programming the Water Softener
UP button
DOWN button
Low Salt
LED Indicator
Display
SELECT / MENU button FIG. 16 RECHARGE button
FIG. 18
When the transformer is plugged into the electrical
outlet, a model code and a test number (example:
J2.0), begin to flash in the faceplate display (See
Figure 17). Then, “12:00” and the words “SET TIME"
begin to flash.
NOTE: If “- - - -” shows in the display, press the
p
UP
or
q
DOWN button until the model code (See
table below) shows in the display. Then,
press the SELECT / MENU button to set, and
change to the flashing “SET TIME" display.
A. SET PRESENT TIME OF DAY
If the words “SET TIME" do not show in the display,
press the SELECT / MENU button a few times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
present time. Up moves the display ahead; down
sets the time back.
FIG. 19
B. SET WATER HARDNESS NUMBER
If you completed the previous step, the words “SET
HARDNESS" should show in the display. Otherwise,
press the SELECT / MENU button several times until
they do.
1 . Press the
p
UP or
q
DOWN buttons to set the
hardness of your water supply, in grains per gallon.
The default is 25. See table below for other units.
2 . When finished setting your water’s hardness num-
ber, press the SELECT / MENU button, and the dis-
play will change to show the “Set Recharge Time”
screen.
FIG. 17
NOTE: Press buttons and quickly release to slowly
advance the display. Hold the buttons down
for fast advance.
2 . When the correct time is displayed, press the
SELECT / MENU button, and the display will
change to show the “Hardness” screen.
Model Code
RBS-9ED SR9
RBS-14ED Sr14
RBS-
24ED
S
R24
1. Press the UP or DOWN buttons to set the
hardness of your water supply, in grains per gallon.
The default is 25. See below for conversion:
Conversion PPM to Grains
Setting= ppm x 0.0584
2. When finished setting your water’s hardness number,
press the SELECT/MENU button, and the display
will change to show the “Set Recharge Time”
screen.
NOTE: Press buttons and quickly release to slowly
advance the display. Hold the buttons
down for fast advance.
2. When the correct time is displayed, press the
SELECT/MENU button, and the display will
change to show the “Hardness” screen.
AQS-9
AQS-14
8