background image

Page 4

Blue Tube Connection- Angle Stop Valve

Water supply line to the system must be from the cold water supply 

line only. Hot water will severely damage your system.

Blue Tube Connection- Faucet Hose

System Module Mounting

Blue Tube Connection - Filtration System

Step 1

 -  Turn off the cold 

water supply to the 

faucet by turning 

the angle stop valve 

completely off. 

Step 2

 -  Open cold water 

sink faucet to relieve 

pressure. 

Step 3

 -  Place a small 

container under the 

cold water angle stop valve to catch any runoff water. 

Disconnect the cold water faucet supply hose from 

the cold water angle stop valve. 

Step 4

 -  Locate the blue 

3/8

"

 tube in the 

parts bag. Remove 

a brass nut, plastic 

delrin sleeve and 

brass insert from 

the parts bag. To 

assemble, place the 

brass nut on the 

blue tube 

fi

rst (Open end out), then the sleeve and 

then push the brass insert all the way into the end of 

the tube. (See Picture). 

Step 5

 -  Secure the blue tube to the cold water stop valve 

using the brass nut. Tighten using an adjustable 

wrench.

Step 1

 -  Locate the threaded 

3/8

"

 male stem 

adapter 

fi

tting in the 

parts bag. Thread 

the stem adapter on 

to the supply hose 

attached to the 

faucet and tighten 

with an adjustable 

wrench. 

Step 1

 -  Mount the system to 

one side of the cabinet 

allowing 3" of clearance 

below the 

fi

lter for 

easy 

fi

lter removal and 

replacement. Mark the 

location for the mounting 

screws on the cabinet 

wall under the sink. In the 

parts bag, locate the two self tapping screws. Using 

an electric drill with a Phillips bit, screw them into the 

cabinet at the marked location. Hang the system on 

the screws using the mounting holes in the bracket. 

Step 1

 -  The tubing is now 

connected on one end 

to the faucet supply, and 

the other end to the shut 

off valve forming a loop. 

This loop of tubing needs 

to be cut at a point that 

provides enough length 

on both sides to connect 

to the 

fi

ltration unit. This 

location varies depending 

on where the 

fi

ltration unit is mounted relative to the 

shut off valve and faucet connection. Cut the blue 

hose at this point, ensuring the ends are square and 

not angled.

Step 2

 -  Connect the 3/8

"

 blue tube coming from the angle 

stop valve into the left side of the 

fi

ltration system (IN), 

by pushing the tubing 

fi

rmly into the quick connect 

fi

tting. Connect the 3/8

"

 blue tube coming from the 

faucet supply hose into the right side of the 

fi

ltration 

system (OUT), by pushing the tubing 

fi

rmly into the 

quick connect 

fi

tting.

Step 2

 -  Locate the 3/8

"

x 3/8

"

 Quick Connect union in the 

parts bag. Push the union on to the 3/8

"

 stem 

adapter 

fi

tting attached to the faucet hose until fully 

seated. 

Step 3

 -  Connect the open end of the 3/8

"

 blue tube to the 

open end of the 3/8

"

x 3/8

"

 Quick connect union 

fi

tting by pushing the tube into the adapter until  

fully seated.

CAUTION

!

3/8" adapter

3/8" quick 
connect union

Other end of 
blue tubing

Summary of Contents for Pure H2O Series









Reviews: