background image

Page 6

  

 

 

 

  

 

 

 

 

 

 

 

 

 

After drilling, remove all sharp edges and make sure the surroundings 

of the sink are cooled before mounting  the faucet.

Step 3

Step 4

Determine desired  location  for  the RO faucet on your sink and place 

a piece of masking tape over where the hole is  to be drilled.  Mark the 

center of the hole on the tape.

Step 1

Using a variable speed drill set on the slowest speed, drill a 1/8“ pilot 

hole through both porcelain and metal casing of sink at the marked 

center of  the desired location. Use lubricating oil or liquid soap to keep 

the drill bit  cool (If drill bit gets hot it may cause the porcelain to crack 

or chip). 

Using a 1 ¼” diamond tip hole saw, proceed to drill the large hole.  Keep 

drill speed on  the  slowest speed and use lubricating oil or liquid soap 

to keep the hole saw cool during cutting.

Step 2

Counter Top / Porcelain & Stainless Steel Sink

Note:

Most sinks are pre drilled with 1 ¼” diameter hole that you can use for your RO faucet. 

(If you are already using it for a sprayer or soap  dispenser, see step 1)

Porcelain sinks are extremely hard and can crack or chip easily.  

Use extreme caution when drilling.  Watts  accepts no responsibility for 

damage resulting from the installation of faucet. Diamond tip bit recommended.

Marble Counter-top

We recommend contacting a qualified contractor for drilling a hole in a marble counter-top.

Drill a Hole for the Reverse Osmosis Faucet

Summary of Contents for GTS350C





















Reviews: