background image

Benchmark 750-3000 Boiler Installation & Startup Manual

 

 SECTION 1 – SAFETY PRECAUTIONS 

 

OMM-0121_D

  •

  GF-205  

  5/9/2019            

Technical Support

  

  (800) 526-0288  

  Mon-Fri, 8 am - 5 pm EST            Page 9  of 122 

 

 SECTION  1:

 

  SAFETY PRECAUTIONS 

 

 1.1  WARNINGS & CAUTIONS 

Installers and operating personnel MUST, at all times, observe all safety regulations. The 
following warnings and cautions are general and must be given the same attention as specific 
precautions included in these instructions.  In addition to all the requirements included in this 
AERCO Instruction Manual, the installation of units MUST conform with local building codes, or, 
in the absence of local codes, ANSI Z223.1 (National Fuel Gas Code Publication No. NFPA-54) 
for gas-fired boilers and ANSI/NFPASB for LP gas-fired boilers. Where applicable, the 
equipment shall be installed in accordance with the current Installation Code for Gas Burning 
Appliances and Equipment, CSA B149.1, and applicable Provincial regulations for the class; 
which should be carefully followed in all cases. Authorities having jurisdiction should be 
consulted before installations are made. 

See  section 1.4  for important information regarding installation of units within the 
Commonwealth of Massachusetts. 

IMPORTANT! 

This Instruction Manual is an integral part of the product and must be maintained in legible 
condition. It must be given to the user by the installer and kept in a safe place for future 
reference. 

 

WARNING! 

  Do not use matches, candles, flames, or other sources of ignition to check for gas leaks. 

  Fluids under pressure may cause injury to personnel or damage to equipment when 

released. Be sure to shut off all incoming and outgoing water shutoff valves. Carefully 
decrease all trapped pressures to zero before performing maintenance. 

  Before attempting to perform any maintenance on the unit, shut off all gas and electrical 

inputs to the unit. 

  The exhaust vent pipe of the unit may operate under a positive pressure and therefore must 

be completely sealed to prevent leakage of combustion products into living spaces. 

  Electrical voltages 

up to 120 VAC (BMK 750 –  2000) and 208 or 460 VAC (BMK 

2500/3000)

  may be used in this equipment. Therefore the cover on the unit’s power box 

(located behind the front panel door) must be installed at all times, except during 
maintenance and servicing. 

  A  single-pole  (120 VAC units) or three-pole (220 VAC and  higher  units)  switch must be 

installed on the electrical supply line of the unit. The switch must be installed in an easily 
accessible position to quickly and safely disconnect electrical service. Do not affix switch to 
unit sheet metal enclosures. 

  

CAUTION! 

  Many  soaps used for gas pipe leak testing are corrosive to metals. The piping must  be 

rinsed thoroughly with clean water after leak checks have been completed. 

  DO NOT use this boiler if any part has been under water. Call a qualified service technician 

to inspect and replace any part that has been under water. 

Summary of Contents for Benchmark Aerco OMM-0122



























































































































Reviews: