WattAge Tubby Cubby Instructions For Final Assembly Download Page 31

31

Visit our website at http://watt-age.globalhobby.com for information on other Wattage products

Telling us what you like and don't like determines what model kits we make and how we make them.  We would
appreciate it if you would take a few minutes of your time to answer the following questions about this kit.  Simply
fold this form on the dotted lines, seal with tape and mail it to us.  

Do not use staples and make sure our address

faces out

.

1) Kit:   

Wattage Tubby Cubby EP # 128436

2) Where did you learn about this kit?

Magazine Ads

Friend

Hobby Shop

Other

Internet

3) What influenced you the most to buy this kit?

Magazine Ads

Price

Type of Model

Box Art

Recommendation

Other

Internet

4) Did you have any trouble understanding the

written instructions?  If yes, please explain.

Yes

No

________________________________________
________________________________________
________________________________________
________________________________________

5) Did you have any trouble understanding any of

the photographs?  If yes, please explain.

Yes

No

________________________________________
________________________________________
________________________________________
________________________________________

6) Were any of the kit parts:

Damaged

Wrong Size

Missing

Wrong Shape

If you checked any of the boxes above, did you
contact our Customer Service Department to
resolve the problem?

Yes

No

7) Was any of the assembly difficult for you?  If

yes, please explain.

Yes

No

________________________________________
________________________________________
________________________________________
________________________________________

8) What did you like most about this kit?

Assembly Manual

Parts Fit

Hardware Supplied

Price

Other

________________________________________
________________________________________
________________________________________

9) What did you like least about this kit?

Assembly Manual

Parts Fit

Hardware Supplied

Price

Other

________________________________________
________________________________________
________________________________________

10) Are you satisfied with the finished model?  If

no, please explain.

Yes

No

________________________________________
________________________________________
________________________________________
________________________________________

11) How does this kit compare to similar kits by

other manufacturers?

Better

As Good

Not as Good

Additional Comments: ______________________________________________________________________

________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________

Cut 

Along Dotted Line

PRODUCT EVALUATION SHEET

Summary of Contents for Tubby Cubby

































Reviews: