Watson Marlow Pumps 504S Manual Download Page 13

13

Product use and decontamination declaration

In compliance with the 

UK Health & Safety at Work Act

 and the

 Control of Substances

 

Hazardous to Health

Regulations

 you, the user are required to declare the substances which have been in contact with the product(s) you

are returning to Watson-Marlow or any of its subsidiaries or distributors. Failure to do so will cause delays in servicing
the product. Therefore, please complete this form to ensure that we have the information before receipt of the
product(s) being returned. A FURTHER COPY 

MUST

 BE ATTACHED TO THE OUTSIDE OF THE PACKAGING

CONTAINING THE PRODUCT(S). You, the user, are responsible for cleaning and decontaminating the product(s)
before returning them.

Please complete a separate Decontamination Certificate for each pump returned. 

RGA No:

 …………………...

1 Company

  Address ……… ................................................................... Postcode ………………………………………

  Telephone ……………………………………………. ................. Fax Number …………………………………..

2.1 Serial Number … … … … … … … … … … … … … ........... (a)………………………………………………….

2.2 Has the Product been used?

(b)…………………………………………………

YES

NO

                                        (c)…………………………………………………

              

                                                                          (d)…………………………………………………

If yes, please complete all the following Sections. If no, please complete Section 5 only

3 Details of substances pumped

3.1 Chemical names:

(a)………………..........................

(b)…………….............................

(c)………………..........................

(d)…………….............................

4 I hereby confirm that the only substances(s) that the equipment specified has
pumped or come into contact with are those named, that the information given is
correct, and the carrier has been informed if the consignment is of a hazardous
nature.

5 Signed …………………………………………………………………………………

  Name  …………………………………………………………………………………

  Position ……………………………………………………………………………….

  Date …………………………………………………………………………………..

3.2 Precautions to be taken in handling these substances: 

To assist servicing, please describe any fault

(a)………… ....................................................

condition(s) you have witnessed

(b)…………  ...................................................

…………………………………………………

(c) ………………...............................................

……………………………………………………………

(d)………………................................................

……………………………………………………………

3.3 Action to be taken in the event of human contact:

……………………………………………………………………………………………………

(a)………………………………………………………………….

……………………………………………………………

(b)………………………………………………………………….

……………………………………………………………

(c)………….………………………………………………………

……………………………………………………………

(d)………….………………………………………………………

……………………………………………………………

3.4 Cleaning fluid to be used if residue of chemical is found:

……………………………………………………………

(a)…………………………………………………………………. 

……………………………………………………………

(b)…………………………………………………………………. 

……………………………………………………………

(c)………….………………………………………………………

……………………………………………………………

(d)………….……………………………………………………… 

……………………………………………………………

Watson-Marlow Bredel Pumps . Falmouth . Cornwall TR11 4RU . England . Tel: 01326 370370 . Fax: 01326 376009

Summary of Contents for 504S














Reviews: