Watson Marlow Pumps 500 Series Installation, Operating And Maintenance Manual Download Page 92

Page: 92 / 157

Table 16 - Acyclic data records

ADI /
Index in
decimal

Name

Access

Type

Description

Edit recipe
volume (ul)

Write

UInt32

Sets active recipe volume

Edit recipe flow

rate (deciRPM)

Write

UInt16

Sets active recipe flow rate

Edit batch size

Write

UInt16

Set current batch size (0 sets
unlimited batch size)

Edit batch start

delay

(deciSeconds)

Write

UInt16

Set the time delay between
the batch start and the first
dose

Edit batch end

delay

(deciSeconds)

Write

UInt16

Set the time delay between
the last dose in a batch and
the end of the batch

Edit recipe start

delay

(deciSeconds)

Write

UInt16

Set the time delay between
the start of the dose and the
pump head startting

Edit recipe end

delay

(deciSeconds)

Write

UInt16

set the time delay between
the pump head stopping and
the end of the dose

Set batch

dispense

direction anti-

clockwise

Write

UInt8

Set batch pump direction to
anti clock wise if set

Edit recipe anti

drip amount

Write

UInt8

Edit the recipe anti drip
amount

Asset number

Read

Unsigned8 array length

21 including NULL

terminator (OctetString)

Read the pump Asset
number

Edit active batch

name

Write

Unsigned8 array length

13 including NULL

terminator (OctetString)

Edit the name of the active
batch

m-530pn-en-09 02-02-22

Summary of Contents for 500 Series






























































































































































Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands

Watson Marlow Pumps 500 Series, Installation, Operating And Maintenance Manual

Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands