background image

Watson Industries, Inc. 

 

GGC-E101 Rev A 08/30/2013 

 

20 

Warning

 

Rough handling, dropping, or miswiring this unit is likely to cause 
damage.  

 
DISCLAIMER 
The information contained in this manual is believed to be accurate and reliable; however, it is the 
user’s responsibility to test and to determine whether a Watson Industries’ product is suitable for a 
particular use. 
 
Suggestion of uses should not be taken as inducements to infringe upon any patents. 
 
WARRANTY 
Watson Industries, Inc. warrants, to the original purchaser, this product to be free from defective 
material or workmanship for a period of two full years from the date of purchase.  Watson 
Industries’ liability under this warranty is limited to repairing or replacing, at Watson Industries’ 
sole discretion, the defective product when returned to the factory, shipping charges prepaid, within 
two full years from the date of purchase.  The warranty described in this paragraph shall be in lieu 
of any other warranty, express or implied, including but not limited to any implied warranty of 
merchantability or fitness for a particular purpose. 
 
Excluded from any warranty given by Watson Industries are products that have been subject to 
abuse, misuse, damage or accident; that have been connected, installed or adjusted contrary to the 
instructions furnished by seller; or that have been repaired by persons not authorized by Watson 
Industries. 
 
Watson Industries reserves the right to discontinue models, to change specifications, price or 
design of this product at any time without notice and without incurring any obligation whatsoever. 
 
The purchaser agrees to assume all liabilities for any damages and/or bodily injury that may result 
from the use, or misuse, of this product by the purchaser, his employees or agents.  The purchaser 
further agrees that seller shall not be liable in any way for consequential damages resulting from 
the use of this product. 
 
No agent or representative of Watson Industries is authorized to assume, and Watson Industries 
will not be bound by any other obligation or representation made in connection with the sale and/or 
purchase of this product. 

 

PRODUCT LIFE 
The maximum expected life of this product is 20 years from the date of purchase.  Watson 
Industries, Inc. recommends the replacement of any product that has exceeded the product life 
expectation.

 

 
 

Summary of Contents for GGC-E101


























Reviews: