Series 97 Fold-out Software Map
[``97]
Process Value
[Safe]
Home Page
Limit Status
Setup Page
[InP1]
Input 1 Menu
[`SEt]
Setup Page
[SEn1]
Sensor Type 1____________
[In`1]
Input 1 __________________
[rL`1]
Range Low 1 _____________
[rh`1]
Range High 1 _____________
[dEC1]
Decimal 1 ________________
[Ftr1]
Input Software Filter 1 ______
[InP2]
Input 2 Menu
[`SEt]
Setup Page
[In`2]
Input 2 __________________
[E`Fn]
Event Function ____________
[E`cn]
Event Condition ___________
[Out1]
Ouput 1 Menu
[`SEt]
Setup Page
[LSid]
Set Limit Active Sides ______
[LhyS]
Limit Hysteresis ___________
[Out2]
Ouput 2 Menu
[`SEt]
Setup Page
[Ot`2]
Output 2 _________________
[hys2]
Alarm Hysteresis 2 _________
[LAt2]
Latching 2 _______________
[sil2]
Silencing 2 _______________
[Sid2]
Alarm Active Sides 2 _______
[Lgc2]
Alarm Logic 2 _____________
[Anu2]
Alarm Annunciation 2 _______
[Out3]
Ouput 3 Menu
[`SEt]
Setup Page
[Ot`3]
Output 3 _________________
[hys3]
Alarm Hysteresis 3 _________
[LAt3]
Latching 3 _______________
[sil3]
Silencing 3 _______________
[sid3]
Alarm Active Sides 3 _______
[Lgc3]
Alarm Logic 3 _____________
[Anu3]
Alarm Annunciation 3 _______
[Out4]
Ouput 4 Menu
[`SEt]
Setup Page
[Ot`4]
Output 4 _________________
[hys4]
Alarm Hysteresis 4 _________
[LAt4]
Latching 4 _______________
[sil4]
Silencing 4 _______________
[Sid4]
Alarm Active Sides 4 _______
[Lgc4]
Alarm Logic 4 _____________
[Anu4]
Alarm Annunciation 4 _______
[Aout]
Analog Output 4 ___________
[Prc4]
Process 4 Type ___________
[A`hi]
Analog Output High ________
[A`lo]
Analog Output Low ________
[ACAL]
Analog Output Offset _______
[BaUd]
Baud Rate _______________
[Addr]
Address _________________
[diSP]
Display Menu
[`SEt]
Setup Page
[UdSP]
Upper Display_____________
[UP`L]
Upper Display
User Limit Message________
[LdSP]
Lower Display_____________
[Lo`S]
Lower Display
User Safe Message________
[Lo`L]
Lower Display
User Limit Message___
_____
[GLbL]
Global Menu
[`SEt]
Setup Page
[C-F`]
C or F ___________________
[`Err]
Input Error Latching ________
Operations Page
[LIM]
Limit Menu
[OPEr]
Operations Page
[L~Lo]
Low Limit Set Point _________
[L~hi]
High Limit Set Point _________
[CAL1]
Calibration Offset ___________
[Mon]
Monitor Menu
[OPEr]
Operations Page
[Pr1`]
Process 1_________________
[L`St]
Limit Status _______________
[AL`2]
Alarm 2 Status _____________
[AL`3]
Alarm 3 Status _____________
[AL`4]
Alarm 4 Status _____________
[E`St]
Event Input Status __________
[ALM]
Alarm Menu
[OPEr]
Operations Page
[A2Lo]
Alarm 2 Low _______________
[A2hi]
Alarm 2 High ______________
[A3Lo]
Alarm 3 Low _______________
[A3hi]
Alarm 3 High ______________
[A4Lo]
Alarm 4 Low _______________
[A4hi]
Alarm 4 High ______________
Factory Page
[`LOC]
Lockout Menu
[FctY]
Factory Page
[OPEr]
Operations Page Mode _______
[`SEt]
Setup Page Lock ___________
[`CAL]
Calibration Menu Lock _______
[dIAg]
Diagnostics Menu
[FctY]
Factory Page
[MdL]
Model Number _____________
[dAtE]
Date of Manufacture _________
[`Sn1]
Serial Number 1 ____________
[`Sn2]
Serial Number 2 ____________
[Soft]
Software ID Number _________
[`rEu]
Software Revision ___________
[ity2]
Input 2 Hardware Enabled_____
[OTY1]
Output 1 Hardware __________
[Oty2]
Output 2 Hardware __________
[Oty3]
Output 3 Hardware __________
[Oty4]
Output 4 Hardware __________
[tout]
Test Output ________________
[dISP]
Test Displays _______________
[hrES]
High Resolution ____________
[AMb]
Ambient Temperature ________
[Acnt]
Ambient A-D Counts _________
[cnt1]
Channel 1 A-D Counts _______
[cnt2]
Channel 2 A-D Counts _______
[LinE]
Line Frequency _____________
Enter your settings on a photocopy
of this page.
The Factory Page also includes
calibration parameters that are
not necessary for everyday use of
the controller. Calibration parame-
ters and procedures are explained
in the Appendix.
