Watlow EZ-ZONE
®
PM Integrated Controller
•
105
•
Chapter 7 Profiling Page
Configuring a Digital Input to Start and Stop a Profile
1. Navigate to the Setup Page and then the Digital I/O menu. From the Home Page, press and hold the
¿
or
Down
¯
key for approximately six seconds where the upper display will show
[``ai]
and the lower dis-
play will show
[`set]
.
2. Press the Up
¿
or Down
¯
key to navigate to the Digital I/O menu. Upper display will show
[`dio]
and
the lower display will show
[`set]
.
3. Press the Advance Key
‰
where the first available digital instance will be displayed in the upper display.
4. Press the Up
¿
or Down
¯
key to select the input of choice.
5. Press the Advance Key
‰
to select the direction (input or output). In this example, select Dry Contact
[iCon]
.
6. Select the level (high or low) that will activate the function by pressing the Advance Key
‰
where the up-
per display will show
[ hig h]
and the lower display will show
[`leu]
.
7. Press the Up
¿
or Down
¯
keys to select the level that will start the profile (high = closed or low = open).
8. Press the Advance Key
‰
to select the function. In this example, select Profile Start / Stop
[ p ;sts]
.
9. Press the Advance Key
‰
to select the function instance (Profile to start).
10. Return to the Home Page by pressing and holding the Infinity Key
ˆ
for approximately three seconds.
Starting a Profile from the Operations Page
1. Navigate to the Operations Page and then the Profile Status menu. From the Home Page, press and hold
the
¿
or Down
¯
key for approximately three seconds where the upper display will show
[``ai]
and the
lower display will show
[oper]
.
2. Press the Up
¿
or Down
¯
key to navigate to the Profile Status
[ p ;sta ]
menu.
3. Press the Advance Key
‰
to enter this menu. The upper display will show
[```1]
and the lower display
will show
[ p ;str]
.
4. Press the Up
¿
or Down
¯
keys to select the Profile or Step to start. In this example select 1.
5. Press the Advance Key
‰
to select the Profile Action Request. The upper display will show
[none]
and
the lower display will show
[ p ;aCr]
.
6. Press the Up
¿
or Down
¯
keys to select the Profile start. The upper display will show
[Prof]
and the
lower display will show
[ p ;aCr]
.
Note:
As soon as the Green Advance key is pressed (step 7 below) the designated Profile or Step (as determined in
step 4 above) will start.
7. Press the Advance Key
‰
to select whether Event 1 will be on or off. The upper display will show
[`off]
and the lower display will show
[ ent1]
.
Note:
This setting will temporally override the profile configuration.
8. Press the Up
¿
or Down
¯
keys to select whether Event 1 will be on or off. This will immediately drive
the Event to the specified state regardless of the Profile configuration.
9. Press the Advance Key
‰
to select whether Event 2 will be on or off. The upper display will show
[`off]
and the lower display will show
[ ent2]
.
10. Press the Up
¿
or Down
¯
keys to select whether Event 2 will be on or off. This will immediately drive
the Event to the specified state regardless of the Profile configuration.
11. Press the Advance Key
‰
to see the current Jump Count. The upper display will show
[```0]
and the
lower display will show
[``jC]
.
11. Return to the Home Page by pressing and holding the Infinity Key
ˆ
for approximately three seconds.