Watkiss P2T User Manual Download Page 35 | Manualshive

Page: 35 / 46

Watkiss P2T User Manual Download Page 35

5 - Error Conditions, Problems and Solutions - Side-Trimmer Message List

Watkiss P2T 2-Knife Trimmer User Manual

31

JAM IN SIDE TRIM

Open and then close the top cover
of the side-trimmer.

Then, if necessary, open the top
cover of the side-trimmer and
check for paper trimmings or
obstructions. Close the top cover
of the side-trimmer.

If the message still does not clear,
use the side-trimmer mains ON/
OFF switch. Turn the side-trimmer
OFF, wait at least 5 seconds and
then turn the side-trimmer ON.

If the problem continues, then call
your service engineer.

Side trim axis moving

The side-trim axis is moving. This
message clears when the adjust-
ment is complete. If the message
does not clear:

Open and then close the top cover
of the side-trimmer.

Then, if necessary, open the top
cover of the side-trimmer and
check for paper trimmings or
obstructions. Close the top cover
of the side-trimmer.

If the message still does not clear,
use the side-trimmer mains ON/
OFF switch. Turn the side-trimmer
OFF, wait at least 5 seconds and
then turn the side-trimmer ON.

If the problem continues, then call
your service engineer.

Message

Information

Reference

«
...
33
34
35
36
37
...
»

Summary of Contents for P2T















































Reviews:

No comments