background image

4

STEP 1

ATTACH BACK HINGES

1.  Locate Bag #1. Some of the contents will be 

used to fasten the Rear Hinges.

REAR HINGES:

2.  Line up the top Rear Hinge (G) holes (Figure 

2.1) with two of the marked holes on the 
back side of the cover. Using the cordless 
drill and square drive bit to fasten the Rear 
Hinge to the cover by using two of the #10 
x 1”square (I) Flat Head screws on the top 
(marked) holes fi rst. Using the 1/8”(3mm) 
drill bit and the bottom two holes of the Rear 
Hinge, drill through the hidden aluminum 
plate followed by inserting two more of the 
same screws in the bottom holes. Repeat 
procedure for second Rear Hinge.

1.  Locate Bag #1. Some of the contents will be 

used to fasten the Side Hinges.

SIDE HINGES:

2.  Line up the top Side Hinge (F) holes (Figure 

3.1) with two of the marked holes on one 
side of the cover. 

3.  Using the cordless drill and square drive bit, 

fasten the Side Hinge to the cover by using 

two of the #10 x 1½”square (J) Flat Head 
screws on the top (marked) holes fi rst.

4.   Using the 1/8”(3mm) drill bit and the bottom 

two holes of the Side Hinge, drill through the 
hidden aluminum plate followed by inserting 
two more of the same screws in the bottom 
holes (Figure 3.1).

 Repeat procedure for Side Hinge on 
opposite side of the cover.

1.  Locate the Right & Left Pivot Assemblies, 

Crosslink, and (4) ¼”-20 Hex Bolts (Figure 
4.1).

2.  Orient (Figure 4.1) on fl oor and attach (A and 

B to C using (4) ¼”-20 Hex Bolts (M).

PROLIFT II INSTALLATION

STEP 3

ASSEMBLE CROSSLINK

Figure 2.1

G

I

4x

STEP 2

ATTACH SIDE HINGES

Figure 4.1

A

C

4x

B

M

Figure 3.1

F

J

4x

Summary of Contents for ProLift II















Reviews: